Hello I want to apply a translation profile but I don't know exactly the difference about applying it on voice port or dial-peer.   Do you guys know the difference?   Also there is a debug where I can see if my translation profile is being used? ... View more

Hello guys   I have a CUCM 10.5 running over UCSC-C220-M3SBE and I want to know how Can I turn off my UCS in a safe mode.   I really don't know so much about UCS but I have made a little reseach and I found that I can turn off my UCS using the Cisco Integrated Management Controller (CIMC) is that correct?   If this is correct I want to know this:   1) The CICM is a separate unit of the UCS? 2) If I shutdown my server from here I still be able to access the CICM to turn it on back? 3) Is there any danger that my UCS don't turn it on back using this method?  ... View more

Hello guys   I have a doubt, I need to enter  web-based management interface of my phone but I am confusing, this one is the SAFE CARE PORTAL  or it is the web you access only with the IP of the Phone (Web Access)? ... View more

Hello Guys   I am trying to logging to my Jabber Windows 12.1.2 Phone Mode Only without IM & Presence but everything I try to logging I receive this message "Cannot Communicate with the server"....   I have done this   1. Create EndUser: Jabber1 with his password  2. Create a New Cisco Unified Client Services Framework 2. In Device Name: CSFJabber1 3. Owner ID: Jabber1 4. Device Security Profile: Cisco Unifid Client Services Framework Standard 5. SIP Profile: Standard SIP Profile 6. Under DN I added My Number and on Users Associated with Line I choosed Jabber1 7. Retuning to users Jabber1 I choosed in Deviced Information the CSF Phone I created 8. When I go to my Windows Jabber and I choose Cisco Jabber Manager 9 or later and I put my IP  Publisher and then I put my credentials Jabber1@IPADDRESPUBLISHER and my password but I get "Cannot Communicate with Server" ... View more

Hello Guys   I am trying to send CARD REPORTS to my email using an SMTP PUBLIC SERVER HOTMAIL with this information that I found in Internet.   Server Name SMTP Hotmail: smtp.live.com (40.97.152.34) Username SMTP Hotmail: your Hotmail account Password de SMTP Hotmail: su Password Account Hotmail Port SMTP Hotmail: 25 o 465 And in the configuration under system --> system parameters --> Mail Parameteres I filled it with the following information:   Mail ID:                                    My account without @hotmail.com Password:                                My Password Account Confirm Password:                   My Password Account again Mail Domain:                            40.97.152.34 Mail Domain Server:                 40.97.152.34   But when I try to send email I got the following error message:   Error Code Error Description 10011 System Error. Contact System Administrator.   I can't use a public SMTP? The configuration is wrong? ... View more

Hello Guys   I am making a SRST Lab where I have a SIDE A with a switch 3750E with Router 2901 where Vlan Voice network is  10.150.0.0/24 and Vlan Network 10.140.0.0/24 and also I have SIDE B with switch 3560X with Router 2811 where Vlan Voice Network  is 192.168.20.0/24   Network WAN 10.90.90.0 /30   In both sides I have one phone 7912 where the calls work perfectly in both sides and when I disconnect my CUCM the phones remain active using SRST with basic configuration where X.X.X.X is the IP GW Voice Vlan   Call-manager-fallback max-conferences 8 gain -6 transfer-system full-consult ip source-address X.X.X.X port 2000 max-ephones 5 max-dn 5   Side A Ext 101 Side B Ext 202   I created the following dial-peer in SIDE A because without it the call from A to B don't establishe   dial-peer voice 10 voip destination-pattern 2.. session target ipv4:10.90.90.2 codec g711ulaw But when I do the same in SIDE B the calls from B to A dont establish...   dial-peer voice 10 voip destination-pattern 1.. session target ipv4:10.90.90.1 codec g711ulaw   Do I need to create something else? I missed something? It could it be maybe a bug? ... View more