Hi folks.... I am trying to setup a home lab where i have a PSTN router which provides E1 connectivity to two other routers (preparing for CCIE). I have no experience in setup up an E1 connection from the PSTN side hence facing issues.... i have checked some initial configuration (INE lab), which i am using as configuration model for my lab setup and D-channel is setup using serial x/x/x:15. I am trying to do the same but i dont get that interface enabled. Below is my configuration.... Please suggest what i can do.... to setup this lab.... ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname PSTN-WAN ! boot-start-marker boot-end-marker ! logging message-counter syslog ! no aaa new-model clock timezone EST -5 clock summer-time EDT recurring network-clock-participate wic 0 network-clock-participate wic 1 network-clock-participate wic 2 ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef multilink bundle-name authenticated ! ! ! ! frame-relay switching isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip fax protocol cisco sip ! ! ! voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw ! ! ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^911$/ /\0/ type any unknown plan any unknown rule 2 /^212\(3942123\)$/ /\1/ type any subscriber plan any isdn rule 3 /^6178632683$/ /\0/ type any national plan any isdn rule 4 /^32141891$/ /34\0/ type any international plan any isdn rule 5 /^6745738932$/ /91\0/ type any international plan any isdn rule 6 /^9004522138$/ /\0/ type any national plan any isdn ! voice translation-rule 2 ! deleting the translations to shortent the config file . . . . ! ! voice translation-profile block-call-into-BR1 translate called 617 ! !. deleteing the translations profile to shorten the configuration . .. . !         voice-card 0 ! ! ! ! ! archive log config   hidekeys ! ! controller E1 0/0/0 clock source internal channel-group 0 timeslots 1-31 description ** SERIAL DATA CONNECTION TO BR1-RTR ** ! controller E1 0/0/1 clock source internal channel-group 0 timeslots 1-31 description ** SERIAL DATA CONNECTION TO BR2-RTR ** ! controller E1 0/1/0 clock source internal channel-group 0 timeslots 1-31 description ** SERIAL DATA CONNECTION TO HQ-RTR ** ! controller E1 0/1/1 clock source internal channel-group 0 timeslots 1-3,16 description ** E1 VOICE CONNECTION TO BR1-RTR ** ! controller E1 0/2/0 clock source internal channel-group 0 timeslots 1-3,16 description ** E1 VOICE CONNECTION TO BR2-RTR ** ! controller E1 0/2/1 clock source internal channel-group 0 timeslots 1-3,16 description ** E1 VOICE CONNECTION TO HQ-RTR ** ! ! ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:0 description ** E1 DATA CONNECTION TO BR1-RTR ** no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 101 interface Serial0/1/0:0 201 ! interface Serial0/0/1:0 description ** E1 DATA CONNECTION TO BR2-RTR ** no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 102 interface Serial0/1/0:0 202 ! interface Serial0/1/0:0 description ** E1 DATA CONNECTION TO HQ-RTR ** no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 201 interface Serial0/0/0:0 101 frame-relay route 202 interface Serial0/0/1:0 102 ! interface Serial0/1/1:0 no ip address ! interface Serial0/2/0:0 no ip address ! interface Serial0/2/1:0 no ip address ! router ospf 1 router-id 10.10.100.2 log-adjacency-changes network 10.0.0.0 0.255.255.255 area 0 ! ip forward-protocol nd ! ip http server no ip http secure-server ! ! ! ! ! control-plane ! ! ! ! ! ! ! dial-peer voice 100 pots incoming called-number . direct-inward-dial ! ! num-exp 916745738932 6745738932 num-exp 1900452.... 900452.... gateway timer receive-rtp 1200 ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 login ! scheduler allocate 20000 1000 end ... View more

hello guys, I am recently decided to ride the CCIE quest for Voice. I am currently in the process of making my lab. I have ordered all my equipment from a Cisco reseller and was checking my equipment that i have ordered are in working condition. However when i connect HWIC-4ESW to Cisco 2811 I dont see the the interfaces. I then checked sh diag and it give the following msg "WIC Slot 2:  Unknown WAN daughter card.WIC module not supported/disabled in this slot" Could anyone of you tell me what I am doing wrong.... I am sure that this module is compatible with 2811 or may be not.... The router has no configuration (all default). IOS version is c2800nm-spservicesk9-mz.124-2.T.bin. Has a AIM-CUE and MFT-2E1 installed in it..... ... View more