How can i collect some evidences of AS-path filter and show to my ISP ? Thanks. Fred ... View more

I have a ticket open with them, but they insist that this is mine problem. If some one can give some hint i can send to my ISP for analyse. Thanks. Fred ... View more

Mohammed, I thinked that exist some way like HSRVP to solve this question. Thanks. Fred ... View more

Amit, Your tip is not my case. Let me explain better. I have two switches cisco and all of my servers have two NIC's. I plug each NIC on differnt switch, but i need do a trunk link between because i have only one inteface to my route. So i want plug eth0 router interface in switch A and eth1 in switch B and remove this trunk. Both eth0 and eth1 have same ip address. If one of switches stop to work my network isn't impacted. Thanks. Fred ... View more

Follow bellow. Current configuration : 3067 bytes ! version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption service sequence-numbers ! hostname router ! boot-start-marker boot-end-marker ! security authentication failure rate 3 log security passwords min-length 6 logging buffered 51200 debugging logging console critical enable secret 5 xxxxxxxxxxxxxxxxxxxxxx ! clock timezone PCTime -8 no network-clock-participate wic 1 no aaa new-model ip subnet-zero no ip source-route ip tcp synwait-time 10 ! ! ip cef ! ! no ip bootp server ip domain name company.com ip ssh time-out 60 ip ssh authentication-retries 2 no ftp-server write-enable ! voice-card 0 no dspfarm ! ! ! voice service voip ! username xxxxxxxxx ! ! controller E1 0/1/0 clock source internal ! controller E1 0/1/1 ! ! ! interface FastEthernet0/0 description ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$$ES_LAN$$FW_INSIDE$ no ip address no ip redirects no ip unreachables no ip proxy-arp ip route-cache flow duplex auto speed auto no cdp enable no mop enabled ! interface FastEthernet0/0.10 encapsulation dot1Q 10 ip address xx.xx.xx.xx 255.255.255.0 (my AS network) no cdp enable ! interface FastEthernet0/0.11 no cdp enable ! interface FastEthernet0/0.12 no cdp enable ! interface FastEthernet0/0.13 encapsulation dot1Q 13 no cdp enable ! interface FastEthernet0/0.14 encapsulation dot1Q 14 no cdp enable ! interface FastEthernet0/1 no ip address no ip redirects no ip unreachables no ip proxy-arp ip route-cache flow duplex auto speed auto no cdp enable no mop enabled ! interface FastEthernet0/1.10 no cdp enable ! interface Serial0/0/0 ip address xx.xx.xx.xx 255.255.255.252 (my isp interface) encapsulation ppp no cdp enable ! interface Serial0/0/1 no ip address shutdown clockrate 2000000 no cdp enable ! router bgp xxxxx (my as number) no synchronization bgp log-neighbor-changes network xx.xx.xx.0 mask 255.255.240.0 (my as range) aggregate-address xx.xx.xx.0 255.255.240.0 as-set redistribute connected redistribute static neighbor xx.xx.xx.xx remote-as xxxx (my isb neighbor and as) auto-summary ! ip classless ip route 0.0.0.0 0.0.0.0 xx.xx.xx.xx (default gateway for my ISP) ip route xx.xx.xx.xx 255.255.255.0 xx.xx.xx.xx (route to one subnet of my AS inside my network point to internal gateway) ! ! no ip http server ip http authentication local no ip http secure-server ip http timeout-policy idle 5 life 86400 requests 10000 ! logging trap debugging no cdp run control-plane ! ! banner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C ! line con 0 login local transport output telnet line aux 0 login local transport output telnet line vty 0 4 privilege level 15 login local transport input telnet ssh line vty 5 15 privilege level 15 login local transport input telnet ssh ! scheduler allocate 20000 1000 ! end Thanks. ... View more

How can we see how many PPS our router or serial interface can handle ? Thanks. Fred ... View more