About goliver

goliver · 08-18-2021

Hi, I am very new to this, so it may be something simple, but here goes. I am using 10.5 AXL with the current xsd and wsdl loaded and the axl-python-zeep-samples-master/axl_update_Service_Parameter.py example file (on Linux). I created the environm...

goliver · 08-17-2021

Hi, I am very new to this, so it may be something simple, but here goes. I am using 10.5 AXL with the current xsd and wsdl loaded and the axl-python-zeep-samples-master/axl_update_Service_Parameter.py example file (on Linux). I created the environm...

goliver · 12-01-2020

Hi, I have a 4321 and I'm trying to configure ERSPAN, but it will not save after I leave config mode: cme-4321#sh ver Cisco IOS XE Software, Version 16.12.03 Cisco IOS Software [Gibraltar], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.1...

goliver · 05-02-2019

Hi, It has been a while since I explored this topic (several years). Our company writes IP phone services for UCM and with almost all companies using a DR site model from a cloud architecture perspective, I need to ask again (without labbing it all ...

goliver · 10-24-2018

Hi, I think the subject says it all. I have an OAM&P network as is common practive, but these switches (bought to run small labs with <= 8 phones will not allow Mgmt access unless there is an *access* port on the switch with link up on the Mgmt vl...

goliver · 09-01-2021

Sorry for the nois - I see that is not a valid entry in the WSDL and schema for List ProcesNode. Guess I need to pull it all in and then walk my dictionary. What is very odd is that the axlsqltookit I downloaded from Cisco actually returns valid da...

goliver · 09-01-2021

Well, I spoke too soon. With this version, the nodeUsage criteria is not even applied: criteria = { 'name': '%', 'nodeUsage': 'Subscriber', 'description': 'UCM%', } ...

goliver · 09-01-2021

David, Thanks for pointing out that project - I switched to Python3 and installed it with pip. All of my issues are gone now. Thanks again! -Greg

goliver · 08-24-2021

Thanks much for your dedication to solving issues David. I was under the impression that Zeep was Cisco's recommened python approach, but I guess not. Are there any other libraries you recommend since Zeep apparently does not create dictionaries ap...

goliver · 08-23-2021

Well, take this scenario (which always succeeds) - I want to do a wildacrd on the description, but still need the individual descriptions returned as well. criteria = { 'name': '%', 'processNodeRole': 'CUCM Voice/Video', 'description': 'U...

Member Since	‎01-04-2006 06:34 PM
Date Last Visited	‎04-26-2023 12:02 AM
Posts	38
Total Helpful Votes Received	10

User Statistics

User Activity

AXL Response (python dict) does not match zeep XML output

AXL Response (python dict) does not match zeep XML output

4321 ERSPAN will not save after config mode ends

IP Phone SRV Queries for IP Phone Services

SG300-10/P Mgmt IP Address not reachable when Mgmt VLAN is PVID on trunk port only

Re: AXL Response (python dict) does not match zeep XML output

Re: AXL Response (python dict) does not match zeep XML output

Re: AXL Response (python dict) does not match zeep XML output

Re: AXL Response (python dict) does not match zeep XML output

Re: AXL Response (python dict) does not match zeep XML output