About Pichet Piriyakitkosol

Pichet Piriyakitkosol · 03-10-2016

Dear All I have issue with ABF for incoming traffic with label. And from my research I found this word "ABF is not supported for incoming labelled/MPLS packets." in this forum. I just want to make sure this is still not support or it work right now....

Pichet Piriyakitkosol · 05-12-2015

Dear All We have existing CRS1 to do the IIG (International Internet Gateway) and will replace soon. We are looking for ASR9K but my boss asking me why we need ASR9K? Why don't we choose N7K which is lower price? I know that ASR9K focus on servic...

Pichet Piriyakitkosol · 02-06-2014

Dear All From cisco document 6500-sup720 and 7600-rsp720 are support IPv4 unicast and MPLS—512,000 routes by default. On my network we have route more than 400K which nearly reach to the limit then I tried to change from 512K to 1007K as below.Router...

Pichet Piriyakitkosol · 11-20-2012

Dear All Normally when we do HSRP with vPC on N7K the device will be Active/Standby in control plane but it will be Active/Active in data plane. In this case any traffic reach to standby device it can forward traffic directly to uplink which is n...

Pichet Piriyakitkosol · 08-18-2012

Hi All I got the problem with L3VPN on ASR9K which has topology as below;CE1<--->PE1<---->PE2<--Gi0/0/0/0-->CE2 << I used subinterface for this link <--Gi0/0/0/1-->CE3 << I usde routed interface for ...

Pichet Piriyakitkosol · 03-01-2021

Hi jrenkenAccording to your discussion with TAC Engineer and your lab test. Is this SMU require reload? ThanksPichet

Pichet Piriyakitkosol · 09-28-2019

Hi Xander How about packet travsers in same NP on trident , typhoon and tomahawk? Are they need forward to fabric or it can be local switch within NP?

Pichet Piriyakitkosol · 02-03-2019

Can we do "hw-module location 0/rsp1/CPU0 reload" instead of remove and re-insert the standby RSP? Thank you

Pichet Piriyakitkosol · 08-05-2018

Hi Xander From my understood ASR9K separate control plane and data plane. But when I look inside architecture then I have question here. - Base on communication control plane messages (such as BFD) between LC-CPU and RSP-CPU, What's channel for thi...

Pichet Piriyakitkosol · 07-27-2017

Hi Xander Someone told me try strict mode and it work for my issue. During damp time ospf neighbor will force to down and waiting for bfd. RP/0/RSP0/CPU0:ASR-1#show ospf neighbor Mon Jul 24 23:33:54.886 UTC * Indicates MADJ interface# Indicates Ne...

Member Since	‎08-12-2004 08:38 PM
Date Last Visited	‎03-09-2021 08:49 AM
Posts	42

User Statistics

User Activity

ABF is not supported for incoming labelled/MPLS packets on ASR9K

Why we need ASR9K for IIG?

High cpu when change "mls cef maximum-route ip" to more than 512K

Is it possible for Nexus 7000 to be HSRP Active/Standby in Data Plane?

ASR9K L3VPN need more than one interface under VRF

Re: CSCvw89875 - Cisco NX-OS Software Unauthenticated Arbitrary File Actions Vulnerability

Re: ASR9000/XR: Troubleshooting packet drops and understanding NP drop counters

Re: Yeah right, it's not possible

Re: ASR9000/XR Understanding and troubleshooting Fabric issues in the A9K

Hi Xander