About vladionescu26

vladionescu26 · 03-08-2025

Hello, I'm having a problem where I configured these routes on CE2:ip route 192.168.10.0/24 20.20.20.1 (R2 Gi0/1)ip route 192.168.10.0/24 30.30.30.1 5 (R3 Gi0/2)And the other way around for 192.168.20.0/24 (VLAN 20). (R2 and R3 are using HSRP, where ...

vladionescu26 · 06-04-2024

Hello, I am having a problem in which the:PE3 doesn't have anything about the LAN behind CE-C1 in its vrf Client-C routing table, but can reach ingress CE-C1;PE1 knows all the routes about the LAN behind CE-C2CE-C1 can reach anything;CE-C2 can only r...

vladionescu26 · 03-24-2024

Hello, I would like to implement an ACL that would only allow returning traffic to the WEBTERM server ( initialised by the WEBTERM, no other traffic).The commands I used were :ip access-list extended REFLEXIVEpermit tcp any 172.16.30.0 0.0.0.255 esta...

vladionescu26 · 08-31-2023

How should I go about configuring IPv6 in this case:I have this topology, in the yellow network I have VLAN 10 and VLAN 20 configured for IPv4, and in the upper-right network there is VLAN 30, VLAN 40 and VLAN 99. I would like to configure IPv6 on ea...

vladionescu26 · 08-31-2023

I have this topology and I don't know why the pings don't work properly across networks, and even in the same network for vlan 10 and 20. Circled with black are the vlans.Every device is properly configured with an ipv6 address and a gateway (SW and ...

vladionescu26 · 03-12-2025

The switches are configured with trunk links to the routers and between them. I removed the SLA configuration which I posted initially because it wasn't working for me."I believe you looking CE2 to send traffic to R2 for the 192.168.10.0/24 traffic a...

vladionescu26 · 03-11-2025

The IP SLA config that I showed was configured on CE2, but since then I removed it from the router.The HSRP timers haven't been changed, and if R2 goes down, the HSRP does flip the active gateway role.Below I have posted the configuration of R2, R3 a...

vladionescu26 · 06-07-2024

Nevermind, I tried again and it is actually working, I probably didn't give it enough time to converge. Thank you sir !

vladionescu26 · 06-06-2024

I made these changes but it did not solve it

vladionescu26 · 06-04-2024

Hello, I used OSPF between the PEs and CEs, I'll provide the configuration below.Also, I think its important to know I used OSPF and EIGRP between the multilayer switches and CE-C1 and redistributed them in the PE1 - CE-C1 OSPF process. On CE-C2, I a...

Member Since	‎08-31-2023 09:23 AM
Date Last Visited	‎04-04-2025 01:02 AM
Posts	15
Total Helpful Votes Received	1

User Statistics

User Activity

Shutdown interface on event

Routes are not advertised between PE routers

Allow returning traffic with ACL established

IPv6 vlan1 [up/down] after configuring IPv4 on multiple VLANS

What would be the necessary IPV6 configs for this topology to gain ful

Re: Shutdown interface on event

Re: Shutdown interface on event

Re: Routes are not advertised between PE routers

Re: Routes are not advertised between PE routers

Re: Routes are not advertised between PE routers