About sivaprakasam81

sivaprakasam81 · 10-27-2009

Hi All, how to enable VPN between these router and allow through PIX? Site I : T1 Router Cisco 1721 Firewall CISCO PIX 506e Site II : T1 Cisco 1721 Firewall PIX506e Site III: Bonded T1 Router :CISCO 12651 Firewall: Cisco PIX 515r Thank you, Siva

sivaprakasam81 · 10-27-2009

Hi All, how to enable VPN between these router and allow through PIX? Site I : T1 Router Cisco 1721 Firewall CISCO PIX 506e Site II : T1 Cisco 1721 Firewall PIX506e Site III: Bonded T1 Router :CISCO 12651 Firewall: Cisco PIX 515r T...

sivaprakasam81 · 10-27-2009

Hi All,how to enable VPN between these router and allow through PIX?Site I :Â T1 Router Cisco 1721Â Â Â Â Â Â Â Â Firewall CISCO PIX 506eSite II : Â T1 Cisco 1721Â Â Â Â Â Â Â Firewall PIX506eSite III:Â Bonded T1 Router :CISCO 12651 Firewall: Cisc...

sivaprakasam81 · 10-19-2009

Hi All,I am currently running cisco IOS and want to load fresh Cisco IOS. I connected the G1/2 into the TFTP server computer. The TFTP server interface is 10.0.0.2. I am unable to assign the ip address to the G1/2. how can I do the file tranfer from ...

sivaprakasam81 · 10-16-2009

Hi All,How to transfer Cisco IOS from computer to 4948 Switch using console connection. Is that possible using Xmodem? Thank you for your inputs.Thank you,Siva

sivaprakasam81 · 11-22-2009

Hi Avilt.You can try with the following Mainline Back up and Restore Configuration Files,refer : http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_tech_note09186a008020260d.shtmlHope this helps!Siva

sivaprakasam81 · 11-21-2009

You can also try Console into the standby supervisor engine and do the necessary changes.refer : https://supportforums.cisco.com/docs/DOC-2778;jsessionid=423442B611EB1F78AF6B66C724FF854B.node0Hope it helps.Siva

sivaprakasam81 · 10-19-2009

Thank you. I have done the tranfer of IOS image via VLAN1. I am unable to delete the VLAN information on the Switch. It is sandalone Switch. Not connected with any switch. Cisco 4900 Switch. Switch#dir cat4000_switch:

sivaprakasam81 · 10-16-2009

Also Xmodem is not a recognised commond in 4948 ROmmon> mode.Thnk you,Siva

sivaprakasam81 · 10-16-2009

The computer is in different network(public). I got two Ethernet card. One is used for Remote desktop and console port. I am not sure, how to do in this.Thank you,Siva

Member Since	‎04-21-2007 04:56 PM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	205

User Statistics

User Activity

how to enable VPN between these router and allow through PIX?

how to enable VPN between these router and allow through PIX?

how to enable VPN between these router and allow through PIX

Cisco ISO Loading to 4900 Switch.

How to transfer Cisco IOS from computer to 4948 Switch using console

Re: Catalyst 4006 Quick Restore

Re: replacing flash on standby sup 5 on 4507r

Re: Cisco ISO Loading to 4900 Switch.

Re: How to transfer Cisco IOS from computer to 4948 Switch using

Re: How to transfer Cisco IOS from computer to 4948 Switch using