About Tavis10284

Tavis10284 · 11-20-2020

Perhaps a newbie question, but:I have a 3560G that is already setup with a few VLANs.VLAN 128 is for workstations. VLAN 50 is for servers. I have added a second 3560G for additional ports for workstations. It has a fresh config. Switch1 (existing) is...

Tavis10284 · 08-18-2009

All,I am working on getting a Cisco 2500 router working with a Linux router (IPcop) that is my gateway out to the Internet. My network topology is attached in .png format. Essentially, I have the IPCop Linux router connected to a D-Link layer 2 gigab...

Tavis10284 · 06-10-2007

Hey all, I hope this isn't a stupid question: I have a Catalyst 5500 series with WS-X5224 cards. I was just wondering if there was a way to configure the LEDs to flash with activity on the port instead of staying lit solid. Thanks!

Tavis10284 · 02-19-2007

Hey all,I am assisting the Cisco CCNA semester 3 students with a lab. The students are using the white and green CCNA 3 and 4 Lab Companion Third Edition book. I am on page 171 step B. When I get to the step to configure the router with "encapsulatio...

Tavis10284 · 03-29-2006

Hello all. I am trying to complete Phase 2 of the CCNA 4 WAN case study. I have the addressing correct according to what the instructor checked and when comparing to everyone else. On phase 2, one of the bullets of items to complete is to Configure a...

Tavis10284 · 11-30-2020

Here's what I came up with that is working:SW1:interface GigabitEthernet0/51switchport trunk encapsulation dot1qswitchport trunk allowed vlan 50,128switchport mode trunkchannel-group 5 mode desirable!interface GigabitEthernet0/52switchport trunk enca...

Tavis10284 · 11-30-2020

And so if I wanted to create an Etherchannel with two gigabit ports assigned to an Etherchannel port, to setup the allowed VLANs on that Etherchannel, would it be something like:interface Etherchannel1 switchport trunk encapsulation dot1q switchpor...

Tavis10284 · 11-20-2020

Well that was easy. Apparently I forgot to apply that to gi0/51 on Switch1. After I did so, I could ping both switches. Thanks for the quick response!

Tavis10284 · 08-30-2009

Sorry - double post.

Tavis10284 · 08-30-2009

I wouldn't say "sucky". It suits my needs for an advanced server/workstation/network tech and my home-business PCs. I love it for that. But apparently doesn't play well with subnetworks and ICMP. My guess is something else needs to be configured on i...

Member Since	‎03-29-2006 02:52 PM
Date Last Visited	‎12-04-2020 09:59 AM
Posts	26
Total Helpful Votes Received	10

User Statistics

User Activity

Configuring a second 3560G to work with primary 3560G with multiple VLANs

Cisco 2500 Router and a Linux Router

Catalyst 5500 LEDs

Problem with "encapsulation dot1q" on 2621/2620 Router

Rip v2 to OSPF Redistribution Problems

Re: Configuring a second 3560G to work with primary 3560G with multiple VLANs

Re: Configuring a second 3560G to work with primary 3560G with multiple VLANs

Re: Configuring a second 3560G to work with primary 3560G with multiple VLANs

Re: Cisco 2500 Router and a Linux Router

Re: Cisco 2500 Router and a Linux Router