Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About AlexPejcic
Stats
Member since
11-15-2010
8
Posts
0
Helpful
0
Solutions
05-15-2012
05:57 AM
Hi Clas, Yes, I did. And I am sorry for not posting back the solution here. The problem was in Port Management: Port Setup screen. I was told by our ISP to disable autonegotiation and put 100 Mbps on all ports. When I reactivated autonegotiation on each port, it all started working fine. Here is a screnshoot of my setup. I hope this helps you as well. Best, Alex
... View more
06-09-2011
02:53 PM
Do you think that I should open a trouble ticket with Cisco, or at least see if this router can be replaced because it is still under warranty?
... View more
06-08-2011
05:28 PM
Hi mpyhala, That did not work either. Not sure where to go from this point. Alex
... View more
06-08-2011
02:40 PM
Hi, Thanks for your quick response. Unfortunately, disabling SPI did not do anything to the data rate problem. I also failed to mention that I changed the link speed from autonegotiate to 100 Mbps full duplex for all ports. Currently, without any load, I get about 14-15 Mbps, should be close to 50 Mbps. Best, Alex
... View more
06-08-2011
12:28 PM
Hi everyone, We currently have RV042 configured as a default gateway. It is connected to another Motorola router provided by our ISP. ISP advertised download speed is 50 Mbps down and 5 Mbps up. When I plug in directly into the ISP router, the measured speed is very close to advertised. However, when I plug in RV042 and then do speed test within the private network, or directly connected to RV042 switch, download datarate is barely 15 Mbps, measured without any other network load. Upload datarate is fine. I tried the firmware update but it seems that my model is not V3, therefore I had to stay at firmware version 1.13.12.19-tm. I did check settings for bandwidth trottling, and even added a rule to allow all services to work at 51200 Kbps, however that did not help. Any ideas? Best, Alex
... View more
Labels:
Created by
AlexPejcic
in Small Business Routers
in Small Business Routers
11-29-2010
08:21 AM
11-29-2010
08:21 AM
Thank you - this works like a charm.
... View more
Created by
AlexPejcic
in Small Business Routers
in Small Business Routers
11-18-2010
11:06 AM
11-18-2010
11:06 AM
Ah so simple. I will try it for a few days and report back when I am 100% sure that it works fine. Thank you!
... View more
11-15-2010
11:48 AM
I am currently using RV042 in the two-WAN backup mode. However, I tried the redundant option and am finding it to give me more bandwidth and better performance than only one of the WANs. My problem is that in the redundant mode, I am unable to use a few websites that I use on a regular basis. One of the sites is our internet hosted time sheet service and their site just goes crazy when I try to access it through the router set up in redundant mode. I am not even able to login to their site, and it is important for my daily work. My question is - can I set up static routes for certain sites so that the router knows to access them through only one of my WANs? For example, if my timesheet software site is 123.123.123.123, and my prefered WAN gateway is 68.68.68.68, can I tell the router to only access this site through the given gateway, even if the router is configured to use either WAN? I have tried static routes and it does not seem to work at all. For example: Site: 123.123.123.123 SM: 255.255.255.0 Gateway 68.68.68.68 When I save this and run the tracert to 123.123.123.123, it goes through the other gateway, and not the one I specified here. Any hints are appreciated. Thanks, Alex P.
... View more
Labels:
05-15-2012
Hi Clas,Yes, I did. And I am sorry for not posting back the solution
here. The problem was in Port M...
06-09-2011
Do you think that I should open a trouble ticket with Cisco, or at least
see if this router can be r...
06-08-2011
Hi, Thanks for your quick response. Unfortunately, disabling SPI did not
do anything to the data rat...
06-08-2011
Hi everyone,We currently have RV042 configured as a default gateway. It
is connected to another Moto...
11-18-2010
Ah so simple. I will try it for a few days and report back when I am
100% sure that it works fine. T...
Public Statistics
| Date Registered | 11-15-2010 11:40 AM |
| Date Last Visited | 08-18-2017 03:55 AM |
| Total Messages Posted | 8 |
