I can get the traffic routed to the cache engine. I can get it to hit the CE and timeout to pull the page, get it to redirect a miss as it should immediately, etc. What I'm facing is EVERYTHING is a miss. All traffic shows as a miss in ACNS and there is 0kb used on the disk. WCCP is enabled, web-cache is obviously being redirected, but why is it missing then bypassing the CE?
... View more
After searching Google and Cisco, here's my setup... 2851 Router running 15.1T CE-NM-BP-80G-K9 in slot 1/0 Bridge group 1 for LAN and Wireless WIC. Goal: Either add the external CE interface to the LAN on the bridge group or use WCCP to cache traffic through the internal interface. I was able to access ACNS once, but I'm completely new to the design and it was only for testing with the IP scheme. I reset the config, reloaded the router and now I can't access ACNS via the web gui nor can I access the network from the CE (ping or ftp). Interface ContentEngine 1/0 Config: ip address 10.0.0.1 255.255.255.0 Service Module ip address 10.0.0.2 255.255.255.0 Service Module external ip address 10.0.1.1 255.255.255.0 Service Module ip default gateway 10.0.0.1 Interface BVI1 ip address 192.168.2.1 255.255.255.0 using dhcp etc Service module config: CE#sh run ! ACNS version 5.5.3 ! ! hostname CE ! http proxy incoming 80 8080 ! ! ! ! ip domain-name mydomain.com ! ! ! ! ! ! ! ! interface FastEthernet external exit interface FastEthernet internal exit ! ! ! wmt evaluate wmt accept-license-agreement wmt enable ! ! ! ! ! ! ip name-server 188.8.131.52 ip name-server 192.168.2.1 ! ! ! ! ! ! ! ! ! ! wccp router-list 1 192.168.2.1 wccp web-cache router-list-num 1 wccp reverse-proxy router-list-num 1 wccp wmt router-list-num 1 wccp version 2 ! ! ! ! ! ! ! ! ! ! username admin password 1 xxx username admin privilege 15 username xxxx password 1 xxx uid 2001 username xxxx privilege 15 ! ! ! ! ! authentication login local enable primary authentication configuration local enable primary ! ! ! ! ! ! ! ! cdm ip 192.168.2.1 ! ! ! ! ! ! ! End of ACNS configuration Here's what I get when attempting to ping: CE#ping 192.168.2.1 connect: Network is unreachable CE#ping 10.0.0.1 connect: Network is unreachable CE#ping 10.0.1.1 connect: Network is unreachable And from the LAN: seth@Sony:~$ ping 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_req=1 ttl=255 time=1.79 ms ^C --- 192.168.2.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.799/1.799/1.799/0.000 ms seth@Sony:~$ ping 10.0.0.1 PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data. 64 bytes from 10.0.0.1: icmp_req=1 ttl=255 time=1.39 ms 64 bytes from 10.0.0.1: icmp_req=2 ttl=255 time=1.93 ms ^C --- 10.0.0.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 1.396/1.666/1.936/0.270 ms seth@Sony:~$ ping 10.0.0.2 PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data. ^C --- 10.0.0.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms seth@Sony:~$ ping 10.0.1.1 PING 10.0.1.1 (10.0.1.1) 56(84) bytes of data. ^C --- 10.0.1.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms Page cannot be displayed when attempting to hit the CE on port 8001 or securely at 8003 although the CE shows it's listening CE#sh gui-server GUI Server is enabled Listen on port 8001 Secured GUI Server is enabled Secured GUI Listen on port 8003 Let me know if there's some other pertinent info, but what am I missing?
... View more