About Glenn Matthys

Glenn Matthys · 06-16-2023

Hello allI have a few SPA512G and SPA514G telephones (firmware version 7.6.2g - latest available) that use XML services for the phonebook, however once in a while when requesting the phonebook, the phone will hang on "Requesting" and the message [CMX...

Glenn Matthys · 10-30-2015

Hi all I have a spoke router (1921) in a dual hub DMVPN setup that keeps spewing this log message: Oct 29 21:13:38 CDT: %NHRP-3-PAKREPLY: Receive Resolution Reply packet with error - insufficient resources(5)Oct 29 21:59:49 CDT: %NHRP-3-PAKREPLY: Re...

Glenn Matthys · 03-02-2014

HelloI'm trying to set up a 3750-48PS-S switch with smartports. This is my (very simple config):macro auto execute GrpMAC remote tftp://192.168.0.1/glenn/smartport_intel.sh!macro auto mac-address-group GrpMAC oui list 000423!macro auto global process...

Glenn Matthys · 12-30-2012

I'm experimenting with VRF's, I'm trying to do NAT from one VRF to another, using a loopback interface. I have one internet VRF (BLUE) and one "local" VRF (RED), and translation has to happen in the RED VRF. I've created a loopback interface which ha...

Glenn Matthys · 10-19-2011

Hi allI'm trying to set up an 1801 router with two WAN interfaces, fastethernet0 and fastethernet1. On the LAN side, I have two subnets. One subnet's internet traffic should be routed over fastethernet0, the other over fastethernet1.I've setup some r...

Glenn Matthys · 03-02-2014

The switch not returning back to its own internal powersupply is normal. You have to usepower rps 1 port 1 mode standbypower rps 1 port 1 mode activeto have the switch switch back to its own powersupply. You could use the EEM to make it revert to the...

Glenn Matthys · 02-27-2014

Make sure you have the firmware for your phone ready with a correctly configured TFTP and DHCP server. Then:* When the phone boots, before the speaker light goes on, hold the # key, keep holding until you see the line lights sequence (this takes a wh...

Glenn Matthys · 12-30-2012

With the help from above, looks like I messed up my NAT configuration but just not saw it. For completeness, the entire working configuration:Current configuration : 2532 bytes!! Last configuration change at 21:48:59 UTC Sun Dec 30 2012 by adminversi...

Glenn Matthys · 12-30-2012

Which CPU bugs are you referring to exactly? Because I upgraded a 2960S last week to 15.0.2-SE and it wouldn't boot anymore (Unexpected exception to CPUvector 2000). I RMA'ed the unit, the new one had no problems with the iOS 15 firmware.

Glenn Matthys · 12-30-2012

Try addingip tcp adjust-mss 1460to interface Dialer0

Member Since	‎06-02-2011 09:12 AM
Date Last Visited	‎06-21-2023 03:27 AM
Posts	42
Total Helpful Votes Received	6

User Statistics

User Activity

SPA 5xx series - [CMXHTTP] thread blocked getting URL.

NHRP log error "Receive Resolution Reply packet with error - insufficient resources(5)"

Smartports - not acting fast enough

NAT not applying to VRF's

1801 router with dual WAN - one subnet for WAN1, other for WAN2

Strange behavior with 3560s and RPS 2300

7961 phone stuck with the speaker light on

NAT not applying to VRF's

Upgrading IOS 12.0 to 15.0 on 2960 and 3560 help?

Outlook vs Cisco Router