Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Ryan Finnie
08-18-2017
Stats
Member since
06-25-2009
11
Posts
0
Helpful
0
Solutions
08-12-2010
11:24 AM
FYI, I had the same type of problem (getting the last 4 line keys to be BLF+SD on a SPA509G), and disabling the unused lines did not help. It turned out the attendant console units were enabled in the config, but I did not have any SPA500S units attached. Disabling the two consoles in the config made BLF on the line keys work again.
... View more
Re: Support for 7900-series hangup beha...
in Voice Systems
01-26-2010
10:19 AM
01-26-2010
10:19 AM
Thank you Steven! However, I went back and double checked that field with the documentation in the SPA500 administration guide, and there appears to be an error in the documentation: Currently it is: Delay after far end hangs up before reorder tone is played. 0 = plays immediately, inf = never plays. Range: 0–255 seconds. Defaults to 5. "inf" is not a valid value, nor is any number above 255; they work the same as 0. Also, it makes it sound like using the upper range will never actually hang up the near end, just sit there. I'm guessing "inf" was used as a placeholder when it was written before the range was defined. It should probably read like so: Delay after far end hangs up before reorder tone is played. 0 = plays immediately. 255 = never plays, near end hangs up immediately after far end hangs up. Range: 0–255 seconds. Defaults to 5. Could this be noted in the errata for the next firmware release? It is listed on both page 150 and 228.
... View more
Created by
Ryan Finnie
in Voice Systems
in Voice Systems
01-12-2010
12:53 PM
01-12-2010
12:53 PM
I was just about to post the same thing, except I saw no difference on SPA50X between 7.3.7 and 7.4.3. There appears to be no way to use the attendant console to transfer calls. Each time (xfer->button, bxfer->button, or even just button while on a call) it just places the current call on hold and dials the SD configured. In my case, I am running Asterisk, with "Server Type" set to "Asterisk", and key configurations like so: fnc=blf+sd+cp;sub=1234@$PROXY;ext=1234 BLF and Call Pickup work as configured, but it's frustrating when the primary use case of an attendant console is to transfer calls.
... View more
12-19-2009
11:41 AM
Is the SPA5xx line (and by extension the SPA9x2 line) compatible with the Linksys WAPPOE modules in any way? I see two scenarios where this might work: 1. The phone itself is 802.3af compatible, so will the Injector part of the WAPPOE talk 802.3af directly to the phone? That way there would only be one cable to the phone, and I can plug in power at the remote end. (We don't have 802.3af switches right now, obviously, otherwise I wouldn't need the WAPPOE.) 2. Barring that, is the physical plug of the WAPPOE Splitter part compatible with the phone's DC port? If so, I could use the WAPPOE the same as if I were attaching it to a WAP, with the Splitter on the phone end and the Injector on the remote end. Thanks, Ryan
... View more
Labels:
12-09-2009
01:48 PM
Asterisk 1.6, SIP. The phones will be provisioned via TFTP, if that matters.
... View more
12-09-2009
12:38 PM
Is there any way to disable the PC port outright? I've got an upcoming deployment of a new office with a dedicated voice VLAN, but VLAN trunking to the phones is not available, and I don't want people plugging PCs into the PC port and getting an address on the voice VLAN. I don't see an option in the configuration to just disable the port. Thanks!
... View more
- Tags:
- spa5xx
Labels:
Re: Support for 7900-series hangup beha...
in Voice Systems
11-10-2009
04:38 PM
11-10-2009
04:38 PM
Yes, SIP via an Asterisk system. Asterisk sends a BYE to the phone when the call is completed, the phone responds to the BYE with an OK, but leaves the call open until the user hangs up.
... View more
08-12-2010
FYI, I had the same type of problem (getting the last 4 line keys to be
BLF+SD on a SPA509G), and di...
Created by
Ryan Finnie
in Voice Systems
01-26-2010
01-26-2010
Thank you Steven! However, I went back and double checked that field
with the documentation in the S...
Created by
Ryan Finnie
in Voice Systems
01-12-2010
01-12-2010
I was just about to post the same thing, except I saw no difference on
SPA50X between 7.3.7 and 7.4....
12-19-2009
Is the SPA5xx line (and by extension the SPA9x2 line) compatible with
the Linksys WAPPOE modules in ...
12-09-2009
Is there any way to disable the PC port outright? I've got an upcoming
deployment of a new office wi...
Created by
Ryan Finnie
in Voice Systems
11-10-2009
11-10-2009
Yes, SIP via an Asterisk system. Asterisk sends a BYE to the phone when
the call is completed, the p...
Public Statistics
| Date Registered | 06-25-2009 03:41 PM |
| Date Last Visited | 08-18-2017 03:55 AM |
| Total Messages Posted | 11 |
