Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Rene Paul Huet
Stats
Member since
08-05-2009
5
Posts
0
Helpful
0
Solutions
Certifications
11-18-2013
01:40 AM
Hi I useLMS 4.2, In fault Monitor I have the folowing messages : Event_Description StateNotNormal Device IP 10.92.8.142 Device Type Switches and Hubs Fault Last Updated At 17-Nov-2013 12:36:25 Component PWR-I@/2058 [Sw2, PS1 Faulty, RPS NotExist ] Component Class PowerSupply Component Event Code 1085 Event Category Environment Event Source DFM Status CRITICAL cisco Env Mon Supply State 6 --> I have just 4 (not 6) But when I check in thw switch everything is ok : #sh env all FAN 1 is OK FAN 2 is OK FAN PS-1 is OK FAN PS-2 is OK SYSTEM TEMPERATURE is OK System Temperature Value: 30 Degree Celsius System Temperature State: GREEN Yellow Threshold : 46 Degree Celsius Red Threshold : 60 Degree Celsius SW PID Serial# Status Sys Pwr PoE Pwr Watts --- ------------------ ---------- --------------- ------- ------- ----- 1A C3KX-PWR-715WAC LIT170517XR OK Good Good 715/0 1B C3KX-PWR-715WAC LIT1705180V OK Good Good 715/0 2A C3KX-PWR-715WAC LIT170517UY OK Good Good 715/0 2B Not Present 3A C3KX-PWR-715WAC LIT170518XH OK Good Good 715/0 3B Not Present SW Status RPS Name RPS Serial# RPS Port# -- ------------- ---------------- ----------- --------- 1 Not Present <> 2 Not Present <> 3 Not Present <> #sh stack-power de Power Stack Stack Stack Total Rsvd Alloc Unused Num Num Name Mode Topolgy Pwr(W) Pwr(W) Pwr(W) Pwr(W) SW PS -------------------- ------ ------- ------ ------ ------ ------ --- --- SP-1 SP-PS Ring 2860 31 669 2160 3 4 Power stack name: SP-1 Stack mode: Power sharing Stack topology: Ring Switch 1: Power budget: 943 Power allocated: 223 Low port priority value: 20 High port priority value: 11 Switch priority value: 2 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: Switch 3 - 7cad.7416.0680 Neighbor on port 2: Switch 2 - acf2.c5c1.4600 Switch 2: Power budget: 943 Power allocated: 223 Low port priority value: 22 High port priority value: 13 Switch priority value: 4 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: Switch 1 - 4c4e.359b.c900 Neighbor on port 2: Switch 3 - 7cad.7416.0680 Switch 3: Power budget: 943 Power allocated: 223 Low port priority value: 21 High port priority value: 12 Switch priority value: 3 Port 1 status: Connected Port 2 status: Connected Neighbor on port 1: Switch 2 - acf2.c5c1.4600 Neighbor on port 2: Switch 1 - 4c4e.359b.c900 I don't find any bug for this ussue. someone has an idea? Many thans for your help
... View more
Labels:
01-23-2013
11:40 PM
Hi, Thank you for the quick response, Version In N7K is 5.2(3a) No DROP in control-plane Best regards
... View more
01-23-2013
07:32 AM
Dear all, I have a strange behavior between a WLC 5508 (version 7.0.116.0) and NEXUS7010. WLC The WLC is configured in DHCP Bridging Mode (it sends DHCP requests without change) Nexus The VLAN interface is configured as follows interface Vlan501 ip access-group acl-int-vlan501-in-1 in no ip redirects ip address 10.12.56.4/21 ip ospf network broadcast ip router ospf 100 area 10.23.0.0 hsrp 51 preempt delay minimum 15 priority 80 ip 10.12.56.1 ip dhcp relay address 10.21.16.2 ip dhcp relay address 10.21.16.3 no shutdown description - VLAN euh-wlan-bg-guest - The "partial" ACL is as follows : ip access-list acl-int-vlan501-in-1 10 remark -- hsrp ---- 20 permit udp 10.12.56.0/29 224.0.0.2/32 eq 1985 log 40 remark -- dhcp ---- 50 permit udp any eq bootpc any eq bootps log 60 ------ The issue is : Clients can not obtain an IP address intermittently If I deactivates the ACL when the problem appears(when the client can not obtain an IP@) the probleme is resolved Note : Before the WLC was connected to Catalyst 6500 and worked properly for 2 years (with same configuration) I saw this note about differences between DHCP relay on the NEXUS7000/NXOS an Ip helper one the 6500/IOS https://supportforums.cisco.com/docs/DOC-14753 Do you think the problem may come from the DHCP relay or ACL on the NEXUS If someone has an idea, do not hesitate Best regards René
... View more
- Tags:
- dhcp
- nexus_7000
- wlan
Labels:
Created by
Rene Paul Huet
in Switching
in Switching
04-20-2010
12:59 AM
04-20-2010
12:59 AM
Dear all, Last week I did an upgrade IOS on a WS-C3750G-24TS-1U. The problem is that after the upgrade the switch has lost the configuration "system mtu 9000”, we created bigs problems with traffic. I'd like to know if this is a bug (or feature) known at Cisco, in my research I found nothing. For information, I upgraded from ipservices-C3750-mz.122-C3750-25.SEB4 to ipservicesk9-mz.122-53.SE1.bin. A show-tech switch in question is attached (after the upgrade and the addition of the command system mtu 9000 "and a second reload) Please can tell me if this problem is know by Cisco? Thank you in advance, René
... View more
Labels:
01-22-2010
02:45 AM
Hi, I wish you a good year 2010 I have a 6506 with 2 WS-X6K-SUP2-2GE (in slots 1 & 2). Card in Slot1 is active and card in slot slot2 is standby. All LEDs are green in card 1 (that's normal) On the Card 2 (redundancy card) The Status and System LEDs are green (that's normal) Active LED is orange (It is normal for this card is in standby). The PWR-MGMT LED is off (and I don't know if it's normal). The synchronization between the two cards are good. A show module shows that all modules are well recognized. A show power shows power is good for all modules. I don't have an error message that indicates a possible problem on the card A show diagnostic module for module 2 indicate state Unknown Various Cisco docs indicate the LED PWR-MGMT may be red or green (but there is no indication on the LED off). The problem is note hardware, because I have the same problem with an other 6500 (6509), I have already change the card. The IOS version is 12.1(26)E6 Please can you tell me if it's normal the power managment LED is of. I'm sorry for my English Best Regards René Note :
... View more
Labels:
11-18-2013
Hi I useLMS 4.2, In fault Monitor I have the folowing messages :
Event_DescriptionStateNotNormalDevi...
01-23-2013
Hi,Thank you for the quick response, Version In N7K is 5.2(3a)No DROP in
control-planeBest regards
01-23-2013
Dear all,I have a strange behavior between a WLC 5508 (version
7.0.116.0) and NEXUS7010.WLCThe WLC i...
Created by
Rene Paul Huet
in Switching
04-20-2010
04-20-2010
/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tableau
Normal"; mso-tstyle-rowband-si...
Public Statistics
| Date Registered | 08-05-2009 12:35 AM |
| Date Last Visited | 06-26-2019 12:04 AM |
| Total Messages Posted | 5 |
