Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Rajdeep Parmar
04-05-2018
Rajdeep Parmar
Member since
04-29-2010
Beginner
Personal Web Page : http://www.att.com/gen/landing-pages?pid=9214
18
Posts
0
Helpful
0
Solutions
05-17-2012
11:37 AM
Hi, Thanks for reply. Here is the config. Please advice !!! a -------------------------------------------------------------------- SW__1__(config)#do sh vt sta VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 7 VTP Operating Mode : Server VTP Domain Name : ABC VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xFB 0x53 0x04 0x9F 0xA9 0x96 0xE1 0x60 Configuration last modified by 0.0.0.0 at 3-1-93 00:01:57 SW__2__(config)#do sh vt sta VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 5 VTP Operating Mode : Transparent VTP Domain Name : ABC VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xFB 0x53 0x04 0x9F 0xA9 0x96 0xE1 0x60 Configuration last modified by 0.0.0.0 at 3-1-93 00:01:57 SW__2__(config)# SW__3__(config)#do sh vtp sta VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 7 VTP Operating Mode : Client VTP Domain Name : ABC VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xFB 0x53 0x04 0x9F 0xA9 0x96 0xE1 0x60 Configuration last modified by 0.0.0.0 at 3-1-93 00:01:57 SW__3__(config)# =================================== SW__1__(config)#do sh vl VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5 Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10, Fa0/11, Fa0/12, Fa0/13 Fa0/14, Fa0/15, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig1/1 Gig1/2 10 HR active 20 ACC active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 Remote SPAN VLANs ------------------------------------------------------------------------------ Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ =============================================================== SW__2__(config)# SW__2__(config)#do sh vl VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Fa0/24, Gig1/1, Gig1/2 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 Remote SPAN VLANs ------------------------------------------------------------------------------ Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ ==================================================== SW__3__(config)#do sh vl VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5 Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10, Fa0/11, Fa0/12, Fa0/13 Fa0/14, Fa0/15, Fa0/16, Fa0/17 Fa0/18, Fa0/19, Fa0/20, Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gig1/1 Gig1/2 10 HR active 20 ACC active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1 enet 100001 1500 - - - - - 0 0 10 enet 100010 1500 - - - - - 0 0 20 enet 100020 1500 - - - - - 0 0 1002 fddi 101002 1500 - - - - - 0 0 1003 tr 101003 1500 - - - - - 0 0 1004 fdnet 101004 1500 - - - ieee - 0 0 1005 trnet 101005 1500 - - - ibm - 0 0 Remote SPAN VLANs ------------------------------------------------------------------------------ ====================================================
... View more
05-17-2012
10:37 AM
Hi All, Secinario : PC1 -- SW1 -- SW2 -- SW 3 -- PC2 SW1 - Server , SW2- Trans , SW3- Client Vlan - 10,20 on swithces. 1) I have created SW1 - Server , SW2- Trans , SW3- Client & created Vl 10,20 on SW1 but not updating Vlan on SW3- client Switch. ??? why ?? might be bcoz of SW2 is trans mode !!! it should bcoz SW2 will not update it's own DB but pass that info to other client SW's. 2) What I did , just change the mode on SW2 - trans to Client & working fine.& able to ping Pc1 to PC2 !!!! ??? 3) Again , I changed that mode back to Trans mode on SW2. still I can ping Pc1 to PC2 !!!! Bcoz, I can see Vl 10 & 20 in that Vlan DB in trans mode. 4) Now, just removed , Vl 10 , 20 from SW2 - trans mode & not able to ping Pc1 to PC2 !!!! Can any one please explain briefly on it ??? why it' happening ?? Thanks in advance.. Thanks, Raj
... View more
Labels:
01-02-2011
08:49 AM
Hi Paolo, Thanks your reply. Can you give me documention or Documention link ( for Qos command & ACL for B.W conrtol )? .So I will try my self. Thanks a lot again .. Thanks, Rajdeep P.
... View more
01-02-2011
02:25 AM
Hi All, I facing one problem , looking for a solution for that one.. Here is my situation. I have a 100MB pipe coming.I have one ASA5505. This is the current backbone to the whole system. I want to send internet to 16 different locations via microwave dishes. So, many problem is my pipe is 100 Mbps , want to cut that large pipes into a bunch of small pipes. Per pipe 2 Mbps.So, I can send this B.W ( 100 Mbps ) to 50 Users. I have only ASA 5505 and L2 switch for Vlan purpose. I heard by using RADIUS server we can do this but I don't know how to do. IF yes, then please share some Docs regarding that one ..Or any other solutions... Please help me.ASAP. Thanks , Rajdeep P.
... View more
Labels:
07-21-2010
07:10 AM
Hi. Thanks for your reply.... As I mentioned I was not able open by using IE v8.... Could you please tell me which IOS you used for SDM...??? Means Entire - IOS Name ... Thanks, Rajdeep P.
... View more
07-14-2010
11:17 PM
Hi All, I just want to know Why I m not able open router in webpage with SDM client software. Just find the attach file here.. My router IP add : 192.168.10.1/24 ( Fa 0/0 ) n cloud is connected to my loop back interface with 192.168.10.50/24 I m albe to ping my loop back as well as Router IP address. but when I tring to open my router in webpage through SDM in IE,Firefox ,or google crome ..it's showing waitng / loading ......loading ... Can u tell me where I did mistake ??? I configured router with CMD's: --- ip http server username cisco pass cisco ------- In SDM client software : ---- Device ID orh hostname : 192.168.10.1 - connect.. showing loading ....loading... tried on all K9 IOS : ---- c3640-jk9o3s-mz.123-14.T7.extracted c7200-jk9o3s-mz.124-19 c2600-adventerprisek9-mz.124-21 Could any one please help me regarding this issue...? Thank in advance, Thanks, Rajdeep P
... View more
- Tags:
- anyconnect
- asa
- asa_5500
- asa_7.x
- configuration
- connectivity_issues
- digital_certificate
- error_message
- ike_protocols
- ios_vpn
- ipsec
- ipsec_negotiation
- isakmp
- nat
- pix_500
- pix_6.x
- pki
- routers
- ssl
- ssl_vpn
- troubleshoot
- vpn
- vpn_client
- vpn_concentrator
- web_vpn
Labels:
07-14-2010
10:55 PM
Hi All, I just want to know may I able to configure switching Lab in GNS3 ???? I read some where we can configure swtiching lab in GNS3 by selecting slot ( NM-16ESW). but by selecting this option in router we can make router as a switch with 16 ports.. but we can't configure our router as a switch. Means We can't apply normal CMD's like Vlan ..etc.... I had used IOS : c3640-jk9o3s-mz.123-14.T7.extracted c7200-jk9o3s-mz.124-19 SW_c3560-advipservicesk9-mz.122-46.SE But Not a single IOS is working as a switch... So, I want to know by using which IOS I can do L3 setiching LAB.???? I want create LAB for Switching only. No need to add router .so, I can make my switch as router for L3 purpose.... Please Give me solution ASAP. Thanks, Rajdeep P.
... View more
- Tags:
- atalyst_2950
- cat_os
- catalyst_2960
- catalyst_3550
- catalyst_3560
- catalyst_3750
- catalyst_4000
- catalyst_4500
- catalyst_5000
- catalyst_5500
- catalyst_6000
Labels:
Created by
Rajdeep Parmar
in Small Business Routers
in Small Business Routers
06-16-2010
12:34 PM
06-16-2010
12:34 PM
Hi... nothing u have to add that ip renge in your network. how ???? open local area network -- properites - - TCP /IP -- Select properties again .. it will open a new window.. where u can config ur ip address manually & DCHP ... select use the following ip add . 192.168.3.4 255.255.255.0 ( ur subnet mas k) 192.168.3.1 ( GW ) 192.168.3.1 ( DNS) then bottom of the page u can see one advance button click on that one put any ip addres of that range .. like ..192.168.3 .240 save it n reboot ur router ... n now try to open in web page.... Thnks, Rajdeep P .
... View more
05-17-2012 11:37 AM
Hi,Thanks for reply. Here is the config. Please advice !!!
a----------------------------------------...
05-17-2012 10:37 AM
Hi All, Secinario : PC1 -- SW1 -- SW2 -- SW 3 -- PC2SW1 - Server , SW2-
Trans , SW3- Client Vlan - 1...
01-02-2011 08:49 AM
Hi Paolo,Thanks your reply.Can you give me documention or Documention
link ( for Qos command & ACL f...
01-02-2011 02:25 AM
Hi All,I facing one problem , looking for a solution for that one..Here
is my situation. I have a 10...
07-21-2010 07:10 AM
Hi. Thanks for your reply....As I mentioned I was not able open by using
IE v8....Could you please t...
07-14-2010 11:17 PM
Hi All,I just want to know Why I m not able open router in webpage with
SDM client software.Just fin...
07-14-2010 10:55 PM
Hi All,I just want to know may I able to configure switching Lab in GNS3
????I read some where we ca...
Created by
Rajdeep Parmar
in Small Business Routers
06-16-2010 12:34 PM
06-16-2010 12:34 PM
Hi...nothing u have to add that ip renge in your network.how ???? open
local area network -- properi...
Public Statistics
| Date Registered | 04-29-2010 09:01 PM |
| Date Last Visited | 04-05-2018 01:18 AM |
| Total Messages Posted | 18 |
