About JW_UK

JW_UK · 06-05-2020

Hi there, I would like to use IP SLA UDP Jitter to alert when the MOS score is greater than 3.5. My config: ip sla 2udp-jitter 1.1.5.1 5000 codec g711alawtos 184threshold 60timeout 500frequency 15history hours-of-statistics-kept 1history enhanced int...

JW_UK · 05-19-2020

Hi, I have a basic UDP-Jitter IP-SLA test: ip sla 1 udp-jitter 1.1.5.1 5000 request-data-size 96 response-data-size 96 threshold 1 timeout 100 frequency 5 branch1#sh ip sla statisticsIPSLAs Latest Operation Statistics IPSLA operation id: 1Type of ope...

JW_UK · 09-23-2019

Hi there, My environment has the following: Branch router, ISR4451-X, version 16.12.1bvManage, version 19.2.0I'd like to configure a IPSEC tunnel to Zscaler, the interface should be sourced from VPN0 so that i can use the public IP address attached t...

JW_UK · 09-10-2019

Does anyone have any experience using Zscaler and Viptela? Zscaler will support 2 x GRE tunnels sourced from the same public IP address.I’m interested to learn if people are using a public IP address for the TLOC-ext subnet to allow the router not co...

JW_UK · 09-06-2019

For cEdge routers that are connected to MPLS and need to establish control connections to the Cisco Cloud, these connections will back haul over MPLS and exit onto the internet via centralised hub firewalls. What NAT solution is recommended at the hu...

JW_UK · 12-04-2020

I have an EEM script that watches IP-SLA then is supposed to send a SYSLOG message, event manager applet linkPoor-rtt authorization bypassevent syslog pattern "Threshold occurred for rtt"action 1.0 syslog msg "internet sla breach for rtt" I see the ...

JW_UK · 06-10-2020

My bad, figured it out For MOS monitoring, the SYSLOG messages need to be read or actioned upon differently to standard RTT. For example a high MOS score score of 5 indicates excellent quality, whereas a low score of 2 indicates poor quality.For RTT ...

JW_UK · 05-20-2020

Hi @paul driver Thanks for your reply, that was my conclusion too, so the IP-SLA will only fail when the responder is unreachable. It seems like a missed opportunity, but do you agree it is not possible to make the IP-SLA fail using, for example, RT...

JW_UK · 11-10-2019

The Cisco BUG ID is not a public one, but the number = CSCvq47600 Zscaler bug ID for the same issue = 58687 Did you clear your crypto session after applying the fix?

JW_UK · 11-08-2019

Yes, turning the feature on, so that it can be disabled. You can verify if you are having the same problem by using the 'show crypto session' command. This will display the IPsec SA traffic flows of your session. In the error condition you will see ...

Member Since	‎10-27-2011 03:27 AM
Date Last Visited	‎01-19-2024 08:06 AM
Posts	30
Total Helpful Votes Received	25

User Statistics

User Activity

IP SLA react MOS not alerting

How to set IP-SLA failure values

IPSEC interface not available from VPN0

Zscaler GRE via TLOC-Extension

NAT for branch controller connections via central FW

Re: EEM script generates syslog message but doesn't go out management vrf

Re: IP SLA react MOS not alerting

Re: How to set IP-SLA failure values

Re: IPSEC interface not available from VPN0

Re: IPSEC interface not available from VPN0