Hi all, I have a EHWIC-4G-LTE-AU in a 1941 router running C1900 Software (C1900-UNIVERSALK9-M), Version 15.4(3)M1, RELEASE SOFTWARE (fc1) and while the EHWIC-4G-LTE-AU is passing cellular traffic just fine, when running sh cellular 0/0/0 all, the following is returned. I was getting sensible information via this command (i.e. full information on EHWIC firmware, bands, MCC, MNC, service, roaming etc) however it seems that I am not now. The LTE LED on the EHWIC is not on however WWAN and RSSI are. EHWIC is still functioning just fine as it is connected and passing data. EHWIC is connected to an external MIMO antenna on the roof of our building. Is this perhaps due to the IOS being 15.4 and below the minimum of 15.5 required for the EHWIC? Any help would be appreciated. Hardware Information ==================== Modem Firmware Version = Modem Firmware built = Hardware Version = International Mobile Subscriber Identity (IMSI) = 1.0 International Mobile Equipment Identity (IMEI) = Integrated Circuit Card ID (ICCID) = Mobile Subscriber Integrated Services Digital Network-Number (MSISDN) = Current Modem Temperature = 255 deg C PRI SKU ID = , PRI version = Profile Information ==================== Profile password Encryption level: 7 Profile 1 = ACTIVE* ** -------- PDP Type = IPv4 PDP address = 10.93.88.145 Access Point Name (APN) = telstra.internet Authentication = None Primary DNS address = 10.5.133.45 Secondary DNS address = 10.4.27.70 * - Default profile ** - LTE attach profile Data Connection Information =========================== Data Transmitted = 869696076 bytes, Received = 958167881 bytes Profile 1, Packet Session Status = ACTIVE IP address = 10.93.88.145 Primary DNS address = 10.5.133.45 Secondary DNS address = 10.4.27.70 Profile 2, Packet Session Status = INACTIVE Profile 3, Packet Session Status = INACTIVE Profile 4, Packet Session Status = INACTIVE Profile 5, Packet Session Status = INACTIVE Profile 6, Packet Session Status = INACTIVE Profile 7, Packet Session Status = INACTIVE Profile 8, Packet Session Status = INACTIVE Profile 9, Packet Session Status = INACTIVE Profile 10, Packet Session Status = INACTIVE Profile 11, Packet Session Status = INACTIVE Profile 12, Packet Session Status = INACTIVE Profile 13, Packet Session Status = INACTIVE Profile 14, Packet Session Status = INACTIVE Profile 15, Packet Session Status = INACTIVE Profile 16, Packet Session Status = INACTIVE Network Information =================== Current System Time = Fri Jul 22 4:42:49 1994 Current Service Status = Unknown Current Service = Unknown Current Roaming Status = Home Network Selection Mode = Automatic Network = Mobile Country Code (MCC) = 0 Mobile Network Code (MNC) = 0 Packet switch domain(PS) state = Cell ID = 0 Primary Scrambling Code = 65535 Radio Information ================= Radio power mode = ON Channel Number = 1300 Current Band = Unknown Current RSSI = -47 dBm Radio Access Technology(RAT) Preference = Unknown Radio Access Technology(RAT) Selected = AUTO Modem Security Information ========================== Card Holder Verification (CHV1) = Disabled SIM Status = General failure SIM User Operation Required = None Number of CHV1 Retries remaining = 0 GPS Information ========================== GPS Info ------------- GPS Feature: enabled GPS Port Selected: Dedicated GPS port GPS State: GPS disabled SMS Information =============== Incoming Message Information ---------------------------- SMS stored in modem = 0 SMS archived since booting up = 0 Total SMS deleted since booting up = 0 Storage records allocated = 25 Storage records used = 0 Number of callbacks triggered by SMS = 0 Number of successful archive since booting up = 0 Number of failed archive since booting up = 0 Outgoing Message Information ---------------------------- Total SMS sent successfully = 0 Total SMS send failure = 0 Number of outgoing SMS pending = 0 Number of successful archive since booting up = 0 Number of failed archive since booting up = 0 Last Outgoing SMS Status = SUCCESS Copy-to-SIM Status = 0x0 Send-to-Network Status = 0x0 Report-Outgoing-Message-Number: Reference Number = 0 Result Code = 0x0 Diag Code = 0x0 0x0 0x0 0x0 0x0 SMS Archive URL = Error Information ================= This command is not supported on 4G modems. Modem Crashdump Information =========================== Modem crashdump logging: off
... View more
I have a SPA525G with some BLF+CP+SD functions on a side car and these mostly work well except sometimes the BLF function randomly stops working after random times. The speed dial function still works however the BLF does not update from green to red when pressed.
Also, sometimes the BLF function sticks so if I call someone via speed dial, the BLF will work however if I hang up before the person answers, the BLF is still flashing.
A reboot of the phone always fixes this issue.
The phone is connected to a Mitel Office 470 system.
... View more