------ My Cisco Reboots daily during business hours. Can I set a 3am reboot? Below is my .cfg for my phone I am not sure which setting is causing the phone to reboot. Any one have any good config files that dont cause teh phone to reboot when it does its refresh? Thank you, Aaron <flat-profile> <!-- Linksys/SIPURA SPA-5xx Phone:ver-1.0:2012-05-10 --> <RTP_Packet_Size> 0.020 </RTP_Packet_Size> <Line_Enable_1_> No </Line_Enable_1_> <Line_Enable_2_> No </Line_Enable_2_> <Line_Enable_3_> No </Line_Enable_3_> <Line_Enable_4_> No </Line_Enable_4_> <Line_Enable_5_> No </Line_Enable_5_> <Line_Enable_6_> No </Line_Enable_6_> <Short_Name_1_> 360 </Short_Name_1_> <Short_Name_2_> 360 </Short_Name_2_> <Short_Name_3_> 360 </Short_Name_3_> <Short_Name_4_> 360 </Short_Name_4_> <Short_Name_5_> 360 </Short_Name_5_> <Short_Name_6_> 360 </Short_Name_6_> <SPA532_Call_Pickup_Code> *8# </SPA532_Call_Pickup_Code> <Line_Enable_1_> Yes </Line_Enable_1_> <Proxy_1_>10.254.10.10 </Proxy_1_> <Register_1_> Yes </Register_1_> <Extension_1_> 1 </Extension_1_> <Short_Name_1_> 555 </Short_Name_1_> <User_ID_1_> 555 </User_ID_1_> <Password_1_> adfasdf </Password_1_> <Display_Name_1_> test phone1 </Display_Name_1_> <NAT_Mapping_Enable_1_> Yes </NAT_Mapping_Enable_1_> <NAT_Keep_Alive_Enable_1_> Yes </NAT_Keep_Alive_Enable_1_> <Default_Ring_1_> 5 </Default_Ring_1_> <Use_Auth_ID_1_> Yes </Use_Auth_ID_1_> <Auth_ID_1_> 555 </Auth_ID_1_> <Preferred_Codec_1_> G711u </Preferred_Codec_1_> <Use_Pref_Codec_Only_1_> no </Use_Pref_Codec_Only_1_> <Dial_Plan_1_> (xx.|*xx.|**xx.|#xx.) </Dial_Plan_1_> <DTMF_Tx_Method_1_> AVT </DTMF_Tx_Method_1_> <DTMF_Process_AVT_1_> yes </DTMF_Process_AVT_1_> <Silence_Supp_Enable_1_> no </Silence_Supp_Enable_1_> <Enable_IP_Dialing_1_> no </Enable_IP_Dialing_1_> <G726-16_Enable_1_> No </G726-16_Enable_1_> <G726-24_Enable_1_> No </G726-24_Enable_1_> <G726-40_Enable_1_> No </G726-40_Enable_1_> 　 　 　 　 　 <Server_Type> Asterisk </Server_Type> <Interdigit_Long_Timer> 5 </Interdigit_Long_Timer> <Interdigit_Short_Timer> 3 </Interdigit_Short_Timer> <Handset_Input_Gain> 6 </Handset_Input_Gain> <Speakerphone_Input_Gain> 6 </Speakerphone_Input_Gain> <Headset_Input_Gain> 6 </Headset_Input_Gain> <Voice_Mail_Number > 555 </Voice_Mail_Number> <Text_Logo > </Text_Logo> <Station_Name> test phone1 </Station_Name> <Call_Return_Code> *69 </Call_Return_Code> <Blind_Transfer_Code> **98 </Blind_Transfer_Code> <Call_Back_Act_Code> **66 </Call_Back_Act_Code> <Call_Back_Deact_Code> **86 </Call_Back_Deact_Code> <Cfwd_All_Act_Code > **72 </Cfwd_All_Act_Code> <Cfwd_All_Deact_Code> **73 </Cfwd_All_Deact_Code> <Cfwd_Busy_Act_Code> **90 </Cfwd_Busy_Act_Code> <Cfwd_Busy_Deact_Code> **91 </Cfwd_Busy_Deact_Code> <Cfwd_No_Ans_Act_Code> **92 </Cfwd_No_Ans_Act_Code> <Cfwd_No_Ans_Deact_Code > **93 </Cfwd_No_Ans_Deact_Code> <Block_CID_Act_Code> **67 </Block_CID_Act_Code> <Block_CID_Deact_Code> **68 </Block_CID_Deact_Code> <Block_CID_Per_Call_Act_Code> **81 </Block_CID_Per_Call_Act_Code> <Block_CID_Per_Call_Deact_Code> **82 </Block_CID_Per_Call_Deact_Code> <Block_ANC_Act_Code> **77 </Block_ANC_Act_Code> <Block_ANC_Deact_Code> **87 </Block_ANC_Deact_Code> <DND_Act_Code> **78 </DND_Act_Code> <DND_Deact_Code> **79 </DND_Deact_Code> <Secure_All_Call_Act_Code> **16</Secure_All_Call_Act_Code> <Secure_No_Call_Act_Code> **17 </Secure_No_Call_Act_Code> <Secure_One_Call_Act_Code> **18 </Secure_One_Call_Act_Code> <Secure_One_Call_Deact_Code > **19 </Secure_One_Call_Deact_Code> <Paging_Code> **96 </Paging_Code> <Call_Park_Code> **38 </Call_Park_Code> <Call_Pickup_Code> **36 </Call_Pickup_Code> <Call_UnPark_Code> **39 </Call_UnPark_Code> <Group_Call_Pickup_Code > **37 </Group_Call_Pickup_Code> <Syslog_Server> 10.254.10.10 </Syslog_Server> <Debug_Server> 10.254.10.10 </Debug_Server> <Debug_Level> 0 </Debug_Level> <Resync_Periodic> 86400 </Resync_Periodic> <Forced_Resync_Delay> 14400 </Forced_Resync_Delay> <Resync_Error_Retry_Delay> 5 </Resync_Error_Retry_Delay> <PC_Port_VLAN_Highest_Priority> 1 </PC_Port_VLAN_Highest_Priority> <Enable_PC_Port_VLAN_Tagging> No </Enable_PC_Port_VLAN_Tagging> <PC_Port_VLAN_ID> 1 </PC_Port_VLAN_ID> <Daylight_Saving_Time_Rule> start=3/-14/7/2:0:0;end=11/1/7/2:0:0;save=1 </Daylight_Saving_Time_Rule> </flat-profile> ... View more

I am currently able to send a config file via tftp and http to my spa504g phone and configure the lines for asterisk. How do I setup a blind transfer button and a direct to voicemail buttom when talking to a caller? I have read on the forum but am still lost. Thank you for any help. Aaron ... View more