Hi everyone and thanks for reading, I have setup a RV120W as primary router at a clients premises using their existing dlink dsl 504T in bridge mode. Everything runs fine except for the PPTPD service will not start. I have many of these in the same types of environments operating perfectly so I know its not because of my usual setup process. Firmware version is 1.0.2.6 and I have also tried 1.0.3.10 which i removed to take that out of the equations. Error log for pptp is below, if anyone has any ideas please let me know. Michael Sun Jun 24 15:17:03 2012(EST) [rv120w][System][NIMF] nimfNetIfaceTblHandler: unable to get LedPinId Sun Jun 24 15:17:05 2012(EST) [rv120w][System][NIMF] nimfNetIfaceTblHandler: unable to get LedPinId Sun Jun 24 15:17:13 2012(EST) [rv120w][System][NIMF] nimfNetIfaceTblHandler: unable to get LedPinId Sun Jun 24 15:17:21 2012(EST) [rv120w][System][PLATFORM] pptpd restart failed Sun Jun 24 15:17:21 2012(EST) [rv120w][System][PLATFORM] pptpdStart failed Sun Jun 24 15:17:21 2012(EST) [rv120w][System][PLATFORM] Error in executing DB update handler Sun Jun 24 15:17:32 2012(EST) [rv120w][System][NIMF] nimfNetIfaceTblHandler: unable to get LedPinId Sun Jun 24 15:17:42 2012(EST) [rv120w][System][NIMF] nimfNetIfaceTblHandler: unable to get LedPinId Sun Jun 24 15:35:26 2012(EST) [rv120w][System][EVTDSPTCH] umiIoctl (43, UMI_CMD_DB_UPDATE(4)) failed. table=AttackChecks6 row=1 ... View more

Hi all, Having setup these systems before this is getting frustrating. I have SIP accounts working fine as needed, the SPA400 is a different story. PSTN incoming is working but the quality is terrible. There is a buzzing noise on PSTN calls (screenshot of SPA400 voice settings attached) I have tried VAD on and off but that has not fixed the issue. The buzzing does not stop you from hearing the caller but makes it quite difficult. I am in Australia and believe I have the regional settings correct. Any suggestions are appreciated. Thanks Michael ... View more

Hi all, thanks for reading. I have the SPA9000/SPA 400 combo with 7 x SPA504G phones. Voip is not issue, incoming/outgoing and line hunt config is fine and voicemail is working as it should. My problem is not incoming pstn calls are terminating at the handsets. As a hunt group I have tried the following under Sip/PBX Parameters/Hunt Groups 400:name="PSTN",100,101,hunt=re;14;1,cfwd=vm1100 In Line 1 (SPA400) contact list I have tried the following with and without line hunt field above. aa 100 100,cfwd=aa & 100,cfwd=vm1100 Line1:100,aa|Line2:100,aa| Line1:100,101,hunt=re;14;1,cfwd=vm1100 Line2:100,101,hunt=re;14;1,cfwd=vm1100|Line2:100,101,hunt=re;14;1,cfwd=vm1100 I am using the same style dial plan & hunt group for Line 2 (sip trunk) I ran a syslog on SPA400 which is attached to this post. Thanks for the help Michael ... View more

Hi all and thanks for reading, I am assigning speed dials to SPA500s attendant console. I am using a script like the one below. fnc=sd;JoeSmith@10.1.1.10;ext=0043xxxxxxx@10.1.1.10;nme=JoeSmith As you can see the only function programmed is sd but the light stays green permanently. The script works but I need to get rid of the lights as it is driving the client mad. Source code of GUI is attached if needed. Thanks Michael ... View more

Hi everyone and thanks for reading this. I have a SPA9000, SPA400 7 x SPA504G. The system has 4 DID's on one trunk, each handset has a different combination available at each. eg Handset 1 Ext 100 - DID 1 Ext 101 - DID 2 Ext 102 - DID3 Handset 2 Ext 103 - DID 4 Ext 104 - DID 1 etc I need to know if there is another way of achieving this as I need to add more handsets and will exceed the 16 Ext limit of the SPA9000. Can I use one ext per handset and achieve the same result? Thanks for reading. Michael. ... View more