About Craig Hunt

Craig Hunt · 01-20-2023

We have a 2 node ISE deployment that does Radius authentication for several WLCs and WLANs. I have the WLANs roughly configured so that half of them use ise01 then ise02 and the other half use ise02, ise01. However I am wondering if there is a dashbo...

Craig Hunt · 09-27-2020

I am looking for some help with intervlan routing on a WS-C3850-48P-E switch running SW version 03.07.05E.I have a few VLANs configured on the switch - 10-Data, 21-Wireless-Management, 105-VoIP.The switch acts as a DHCP server for the 21 and 105 vlan...

Craig Hunt · 04-17-2020

I am having an issue configuring SSH on a Catalyst 9300 switch. IOSXE 16.6.3.After generating the RSA, SSH gets enabled but I see "%SSH: Failed to encode IOS ASN.1 to SECSH format" in the output of 'show ip ssh'. I have tried regenerating the key mu...

Craig Hunt · 03-25-2020

I am hoping someone can help me with a new ISE 2.6 implementation. We have TACACS+ device management working very well but now we have been asked to give very limited switch CLI access to some helpdesk staff. Basically they should be able to do any...

Craig Hunt · 09-12-2019

We have an overhead paging system at a hospital that we are able to dial a 4-digit number to access. Everything works fine but we now have a request to not allow any external callers to access this DN. Only calls initiated internally should be able...

Craig Hunt · 09-28-2020

BINGO!! Thanks Richard. That was it. I added a static route on the 2911 back to the 3850 and my PC now has access to everything. I guess I was incorrectly assuming that if there was a route from the PC > Switch > ISR, that it would automatically ...

Craig Hunt · 09-27-2020

uggggh. I think I jumped the gun. I can now access the 192.168.21.0/24 subnet while I am connected via vlan10 (192.168.10.0/24) but still can't get to the 192.168.105.0/24 subnet. Edit: I can actually ping all vlan interfaces hosted on the switch ...

Craig Hunt · 09-27-2020

Guys!! Thank you so much for your help. I can now access everything from the PC. I do believe it was my default gateway on my PC. I think I had it set to 192.168.10.1 (doesn't exist). Rookie mistake! I changed it to .2 and can now access the ot...

Craig Hunt · 09-27-2020

Really appreciate all your help guys. Really helping me learn.My PC is running Ubuntu. I have the IP configured as 192.168.10.99 and the gateway is 192.168.10.2 I can ping the Vlan10 interface of the switch at 192.168.10.2. Additional output from ...

Craig Hunt · 09-27-2020

Hi balaji.bandi. Thanks for your quick reply. Currently this is just set up in a lab-type setting for learning purposes but I hope to get it connected to the internet next for a production-type setting.So.....Yes, I don't have DHCP on the 3850 so I ...

Member Since	‎11-22-2016 05:43 AM
Date Last Visited	‎02-14-2024 12:05 AM
Posts	35
Total Helpful Votes Received	15

User Statistics

User Activity

ISE Authentications Load Balance Graph

Looking for help with intervlan routing on 3850 switch

Catalyst 9300 - %SSH: Failed to encode IOS ASN.1 to SECSH format

Help with TACACS+ Command Sets in ISE 2.6

CUCM - Block all inbound external calls to certain DN

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch

Re: Looking for help with intervlan routing on 3850 switch