About Eric.Biggie

Eric.Biggie · 08-05-2011

Hello VPN guru's,I'm running into a little issue here...I have a Cisco RV110W small business router setup at my home. It has one of those HTML GUI interfaces, check the boxes, etc.., to get things working. Basically, your typical home router with VPN...

Eric.Biggie · 07-21-2011

Hello all, I'm having a problem pinging a network and would appreciate some help .I have a router setup with fa0/0: 10.20.30.109 /24. and fa0/1: 172.16.1.1 /24. using rip v2. Any device on the 172.16.1.0 network can ping anything on the 10.20.30...

Eric.Biggie · 06-06-2010

Hello all,Can someone please help me get outbound calls routed out to my PSTN. I've tried using MGCP and now H.323 and it still doesn't work. I've been able to route an inbound call to one of my IP phones but I had to use "connecton plar 7001" to e...

Eric.Biggie · 06-05-2010

Hello All,I live outside the U.S. and need help making route patterns in CUCM7. I have all inside network IP phones working and the gateway is setup and being controlled by MGCP. The gateway is a 3725 with 4FXO mod supporting 4 analog lines out to...

Eric.Biggie · 04-20-2010

Hello all,I've successfully loaded CUCM7 in VMware server, and I can get to the CUCM7 GUI just fine. But it's assigned an ip address by dhcp, ie: 192.168.0.*** from my router. I want to assign the CUCM server a static IP of 172.30.100.14, but it doe...

Eric.Biggie · 08-11-2011

Thanks Raga. You're correct, the RW110W will not support tunnels. I sure wish I would have done a bit more research before I bought it. The packaging said up to 5 VPN's, can support IPSEC PPTP and L2TP. I just assumed that meant I could VPN anothe...

Eric.Biggie · 07-23-2011

Ok, I couldn't get the extra lab router to work correctly either. I did however figure out how to add entries in the RV110W routing table. I eventually added a loopback interface 172.16.2.100 on the 3725 CME voice router, and added networks 172.16...

Eric.Biggie · 07-21-2011

Hello Jon,the 10.20.30.x router is a Cisco RV110W. It's just a small home router with HTML interface setup, etc. In the networking tab it has an option to pick "gateway" or "router". It's set for gateway right now but has RIPv2 enabled automatical...

Eric.Biggie · 07-21-2011

Hi Antonio, I removed passive-interface FastEthernet0/0 and I still can't ping 172.16.1.1 from a pc on the 10.20.30.1 network. Yes there is a router connected to fa0/0. It's my home DSL router, a Cisco RV110W. I have a small switch and a few pc's ...

Eric.Biggie · 07-21-2011

Hello, thanks for your reply . Here's the show run (less phone numbers, etc..):Router#show runBuilding configuration...Current configuration : 10084 bytes!! Last configuration change at 19:26:03 GERMANY Thu Jul 21 2011! NVRAM config last updated at ...

Member Since	‎02-28-2008 03:40 AM
Date Last Visited	‎11-18-2020 09:23 AM
Posts	30

User Statistics

User Activity

VPN with 2801

problem pinging network

Routing call to PSTN via CUCM7

Route Pattern Help

How do I assign a static IP for CUCM7 in VMware?

VPN with 2801

Re: problem pinging network

Re: problem pinging network

Re: problem pinging network

problem pinging network