About david.reid66

david.reid66 · 11-10-2015

Hi Guys, Calls drop on a Jabber (Video) client after 30 seconds when dialling into a TelePresence Server. This happens if the client is connected to the customer wireless. If the Jabber client is connected through the customer LAN or from home (o...

david.reid66 · 10-23-2015

TelePresence Conference displaying “conference number” instead of H.323 name/alias as the “Display Name”. A SIP registered system displays its SIP URI which is fine. Currently none of the 100+ systems are set up as SIP and I don’t want to force every...

david.reid66 · 08-19-2014

Hi Guys,The Conductor prerequisites for latency clustering (from the TelePresence-Conductor-Clustering-Cisco-VCS-B2BUA-Deployment-Guide-XC2-3.pdf) state “If peers are deployed on different LANs, there must be sufficient connectivity between the netwo...

david.reid66 · 11-26-2013

Hi Guys,I need clarification on the “Collation” settings for the manually created databases for tmsng and tmspe.The TMS 14.3.2 install guide quotes a collation for tmsng of: Latin1_General_CI_AIThe TMSPE 1.1 deployment guide quotes a collation for tm...

david.reid66 · 10-01-2012

Hi There,I have MeetingPlace (MP) 8.5 with Webex scheduling setup and I want to enable video conferencing on the MP server. You are supposed to be able to enable video by changing the “Video enabled” option (under Media Resource Configuration) from N...

david.reid66 · 11-12-2015

Hi James, Thanks for your assistance. I’ll speak with the customer about the points you raise. In a trace I took last week on the TPS, I’ve removed/replaced the customer domain name with <domain> to hide it. I’ve done the same with the SIP log ...

david.reid66 · 10-23-2015

Hi Patrick, I don't have access to the endpoints to check what the SystemUnit settings are but is that the same as the "System Name" field in an 880MXP as I've looked at a Tandberg MXP guide and can find the "System Name" but not the "SystemUnit" fie...

david.reid66 · 10-23-2015

Hi Patrick, As you say, the number should be the H.323 ID but it’s a very long “conference” number in this case: 1de31ad3-31dd-4715-8e81-8b1d6f7702a1 You get about half of the number on screen as it’s too long. It’s as if the Conductor/TPS doesn’t kn...

david.reid66 · 09-30-2014

Hi Jonathan,Thanks for the feedback. I've left both Conductors running and it's been fine so far.I've made a few changes to the master and it has replicated to the slave ok but I don't think the customer will be changing the config much now.If the cu...

david.reid66 · 09-18-2014

Hi Wayne,The good news is that I went through the install again and this time it worked fine. I must've made a configuration error of some kind initially. My original point about the RTT was what would happen with excessive delay, what should I look ...

Member Since	‎12-01-2006 03:25 AM
Date Last Visited	‎01-04-2018 06:04 AM
Posts	31

User Statistics

User Activity

Calls drop on a Jabber (Video) client after 30 seconds when dialling into a TelePresence Server

TelePresence Conference displaying “number” instead of H.323 name/alias as the “Display Name”.

Conductor clustering and latency

TMS databse Collation setting - Accent Sensitive or not?

MeetingPlace 8.5 and Video with Webex Scheduling

Hi James,

Hi Patrick, I don't have

Hi Patrick, As you say, the

Hi Jonathan,Thanks for the

Hi Wayne,The good news is