Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About sayeedibrahim
01-18-2019
Stats
Member since
12-27-2009
82
Posts
5
Helpful
0
Solutions
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
03-23-2014
03:27 AM
03-23-2014
03:27 AM
Hi Will appreciate if you can guide me here: 1. 9951 phones working fine with firmaware sip9951.9-0-1SR1 2. Added a new 9951 phone but it does not register as the firmware it is using is sip9951.9-2-2SR1-9 From: <sip:2823@172.29.27.250>;tag=c40acbe137ec00203f83cc41-4d566524 To: <sip:2823@172.29.27.250> Call-ID: c40acbe1-37ec0016-57515da2-200a6715@192.168.20.68 Max-Forwards: 70 Date: Sun, 23 Mar 2014 09:38:56 GMT CSeq: 118 REGISTER User-Agent: Cisco-CP9951/9.2.1 Contact: <sip:3BDA758-1176@192.168.20.68:5060;transport=udp>;+sip.instance="<urn:uuid:00000000-0000-0000-0000-c40acbe137ec>";+u.sip!devicename.ccm.cisco.com="SEPC40ACBE137EC";+u.sip!model.ccm.cisco.com="537" Supported: replaces,join,sdp-anat,norefersub,extended-refer,X-cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-5.1.0,X-cisco-xsi-8.0.1 Content-Length: 0 Reason: SIP;cause=200;text="cisco-alarm:24 Name=SEPC40ACBE137EC ActiveLoad=sip9951.9-2-2SR1-9.loads InactiveLoad= Last=phone-reg-rej" Expires: 3600 3. When i check the configuration file , the load defined is as follows: #more flash:/its/SEPC40ACBE137EC.cnf.xml | i load <loadInformation>sip9951.9-0-1SR1</loadInformation> 4. Output from Flash: CME#sh flash | i 9951 10728 Mar 22 2014 18:11:58 +03:00 dkern9951.100609R2-9-0-1SR1.sebn 1474604 Mar 22 2014 18:12:20 +03:00 kern9951.9-0-1SR1.sebn 27423488 Mar 22 2014 18:13:06 +03:00 rootfs9951.9-0-1SR1.sebn 143448 Mar 22 2014 18:13:34 +03:00 sboot9951.100609R2-9-0-1SR1.sebn 1278 Mar 22 2014 18:13:54 +03:00 sip9951.9-0-1SR1.loads 67000 Mar 22 2014 18:14:26 +03:00 skern9951.022809R2-9-0-1SR1.sebn 5. TFTP Settings: tftp-server flash:dkern9951.100609R2-9-0-1SR1.sebn tftp-server flash:kern9951.9-0-1SR1.sebn tftp-server flash:rootfs9951.9-0-1SR1.sebn tftp-server flash:sboot9951.100609R2-9-0-1SR1.sebn tftp-server flash:sip9951.9-0-1SR1.loads tftp-server flash:skern9951.022809R2-9-0-1SR1.sebn 6. Voice Register global Settings: voice register global mode cme source-address 172.29.27.250 port 5060 max-dn 35 max-pool 20 load 9971 sip9971.9-3-2SR1-1 load 9951 sip9951.9-0-1SR1 load 8961 sip8961.9-3-2SR1-1 timezone 31 date-format D/M/Y mwi reg-e164 voicemail 8999 tftp-path flash: file text create profile sync 0001830533202149 camera video
... View more
Labels:
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
11-03-2013
03:55 AM
11-03-2013
03:55 AM
Thanks all for sharing your knowledge on this topic. Our cisco account manager also gave us a very nice document to read which clarified further for me to proceed with finalizing our solution. http://www.cisco.com/en/US/docs/voice_ip_comm/cusrst/requirements/guide/srs91spc.html After referring to the compatibility tables in this link I am going to finalize to proceed with proposing SRST v9.1 as it supports CUCMv5.x.
... View more
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
10-27-2013
03:50 AM
10-27-2013
03:50 AM
Hi Aman Thnx for a quick reply. After reading the following posts I understood that SRST does not depend on Call manager version but would give problems with phone loads in case the SRST version was lower than the CUCM version. In my case the cucm version will be older than the SRST version so I assume not to face this problem but i do not want to take chances so i will wait for more replies. https://supportforums.cisco.com/thread/2207604 https://supportforums.cisco.com/thread/2011367
... View more
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
10-27-2013
03:13 AM
10-27-2013
03:13 AM
Hi One of my client uses CUCM V5.1.3 and now needs SRST to be deployed for them. Are there any limitations related to compatibility between CUCM v5.1.3 and SRST ver 9.x. Appreciate the replies. Thanks Ibrahim Sayeed
... View more
- Tags:
- cucm
- cucm_5.1.3
- srst
Labels:
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
07-29-2013
12:31 AM
07-29-2013
12:31 AM
Yes 'MTP Required option" was checked. The issue got resolved when i unchecked the option. Thanks Chris.
... View more
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
07-28-2013
09:32 AM
07-28-2013
09:32 AM
Hi Chris Thanks for the suggestion. I will check and confirm on that.
... View more
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
07-28-2013
06:57 AM
07-28-2013
06:57 AM
Hi I will appreciate support for a situation I have encountered for one customer. The server hardware is MCS 7825. A total of upto 600 IP phones registered. I noticed that the conference bridge is registered on the subsriber. Client have 1 Publisher & 1 Subscriber. Th CUCM version is 6. When a call is received from a telco line/mobile, end user answers calls but cannot transfer or take another party in a conference call as the softkeys are non functional. This is not the case for extension to extension communication. Also when i naviagte within the cucm gui, i noticed a delay to navigate between pages. Thanks Ibrahim SAYEED
... View more
Labels:
03-13-2013
03:21 AM
Hi I am trying to configure RSPAN for one of my client. They have Server-Client VTP architecture. Voice Recording Server is connected to C4507. Agents are connected to C2960 and C3750. I got 2 sessions configured and the connectivity is a as follows: 1. Voice Recording Server-----C4507-----C2960-----C2960-----Agent IP Phones (Session 1) 2. Voice Recording Server-----C4507-----C3750-----Agent IP Phones (Session 2) Recording works with Session-2 but not with Session-1. I understand the problem could be due to multiple reasons: 1.1. C2960 is working in client VTP mode so i cannot add remote span command under the vlan configuration. 1.2. C2960 has LANLITE IOS image which i am not sure if it supports Remote Span. Looking forward for valuable advices. R Ibrahim SAYEED
... View more
Labels:
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
02-18-2013
08:24 AM
02-18-2013
08:24 AM
Thanks Chris. Would it be ok, if i replace the old CUCME IP with new CUCME IP inside the cue configuration console. Can you provide me the link to access the licensing web portal. Would it better if i send an email to licensing team. Thanks Ibrahim SAYEED
... View more
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
02-18-2013
08:13 AM
02-18-2013
08:13 AM
Hi Site A- CUCME + CUE Site B - CUCME CUE from Site A to be pulled out and used at Site B. I have already installed the ISM module at Site B and i can access it but it not able to communicate with CUCME to fetch phones information as it was previosuly configured with a different CUCME IP. I am confused it resettign to factory default will remove my licenses already installed. Thanks for your suggestions/support. Ibrahim SAYEED
... View more
Labels:
Created by
sayeedibrahim
in Other Network Architecture Subjects
in Other Network Architecture Subjects
12-04-2012
01:34 AM
12-04-2012
01:34 AM
Hi I want to upgrade the IOS for one ASR device. I cannot downlaod the latest IOS from cisco website. I want to purchase Smartnet so that I can get access to download the IOS. I will appreciate you guys can help me decide which part should I request the Smartnet for so that I can get access to downlaod IOS or if not get the IOS published by TAC. R Ibrahim Sayeed
... View more
Labels:
Created by
sayeedibrahim
in IP Telephony and Phones
in IP Telephony and Phones
10-21-2012
11:59 PM
10-21-2012
11:59 PM
just to update. I could not succeed in making the phone and PC work with different vlans. interface gi0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk native vlan 10 ** with this configuration both IP phone and PC take IP Address from DHCP server but from the same ip subnet. ** I opened a TAC case to get help but believe me the assigned engineer's response has been far below expectations.
... View more
10-16-2012
05:21 AM
Hi Thanks for the suggestions. I have got 7206 VXR at both ends. Below is how the interfaces are configured. One of my Customer needs to change to a higher MTU size but ISIS stops working whenever I try to increase the MTU size. It works if i decrease the mtu. For testing i used "clns mtu 1500"and ISIS went down but when I used "clns mtu 90", it works fine.
... View more
10-16-2012
02:58 AM
Hi I will appreciate recomedations and suggestions to help me configure and run ISIS between two routers with large MTU size.
... View more
Labels:
03-23-2014
HiWill appreciate if you can guide me here:1. 9951 phones working fine
with firmaware sip9951.9-0-1S...
Created by
sayeedibrahim
in IP Telephony and Phones
11-03-2013
11-03-2013
Thanks all for sharing your knowledge on this topic.Our cisco account
manager also gave us a very ni...
Created by
sayeedibrahim
in IP Telephony and Phones
10-27-2013
10-27-2013
Hi AmanThnx for a quick reply. After reading the following posts I
understood that SRST does not dep...
Created by
sayeedibrahim
in IP Telephony and Phones
10-27-2013
10-27-2013
HiOne of my client uses CUCM V5.1.3 and now needs SRST to be deployed
for them. Are there any limita...
07-29-2013
Yes 'MTP Required option" was checked. The issue got resolved when i
unchecked the option. Thanks Ch...
07-28-2013
HiI will appreciate support for a situation I have encountered for one
customer.The server hardware ...
03-13-2013
HiI am trying to configure RSPAN for one of my client. They have
Server-Client VTP architecture.Voic...
Created by
sayeedibrahim
in IP Telephony and Phones
02-18-2013
02-18-2013
Thanks Chris.Would it be ok, if i replace the old CUCME IP with new
CUCME IP inside the cue configur...
Created by
sayeedibrahim
in IP Telephony and Phones
02-18-2013
02-18-2013
HiSite A- CUCME + CUESite B - CUCMECUE from Site A to be pulled out and
used at Site B. I have alrea...
Created by
sayeedibrahim
in Other Network Architecture Subjects
12-04-2012
12-04-2012
HiI want to upgrade the IOS for one ASR device. I cannot downlaod the
latest IOS from cisco website....
10-22-2012
HiI would like to know the recomended methods for back up and restore of
cucm. I am using version 7....
Created by
sayeedibrahim
in IP Telephony and Phones
10-21-2012
10-21-2012
just to update. I could not succeed in making the phone and PC work with
different vlans.interface g...
Public Statistics
| Date Registered | 12-27-2009 09:38 PM |
| Date Last Visited | 01-18-2019 04:06 AM |
| Total Messages Posted | 82 |
| Total Helpful Votes Received | 5 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 6 | |
| 5 | |
| 8 | |
| 3 | |
| 3 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
