About pattyj

pattyj · 04-01-2020

Hello Community, Is there a correct syntax to add multiple eem built in variables to a single statement like below if supported? action 2.0 snmp-trap strdata "$_syslog_msg, $_info_routername"oraction 2.0 snmp-trap strdata "$_syslog_msg / $_info_route...

pattyj · 03-31-2020

I'd like to use this config for EEM in the Nexus 5K. The Nexus only takes the first event syslog occurs statement so I don't understand why it's losing the 2nd statement. See below for sh run eem. Nexus 5548 version 7.0(7)N1(1). Am I violating a sy...

pattyj · 10-25-2018

How can I find the running Prime job via the Prime CLI? Assuming there is a PID per each job that can be manually killed. Ran a system reboot job that was reloading routers. Prime said the job stopped or timedout but routers were still rebooting a...

pattyj · 10-01-2018

Is it possible to create a custom dynamic IOS software version Dashlet in Cisco Prime. So idea is a user can select a device family and see software versions on that device familiy dynamically. A visual on demand interactive dashboard for IOS versi...

pattyj · 05-18-2018

Trying to use CLI Templates to push this command to a bunch of ISR4Ks but it has a yes/no prompt that needs a response so trying the #INTERACTIVE option but have not gotten it to work. Tried various permutations but they all fail. There is not much ...

pattyj · 10-25-2018

Found out from TAC it's already built into Prime however it is not on Prime 3.3 but back on Prime 3.4 and was present on Prime 3.2. TAC filed a bug.

pattyj · 10-25-2018

This ended up working. The verbiage in the brackets [ ] is what it wanted for IQ then followed by the Response <R>yes. The IQ section wants what is in brackets. Documentation not clear to me but found out from TAC engineer. #MODE_ENABLE#INTERACTI...

pattyj · 04-19-2018

Figured it out. Missing command snmp-server user username groupname remote 1.1.1.1 v3 auth md5 password priv aes 128 password and snmp-server source-interface informs Loopback0

pattyj · 11-11-2010

Hi,I'm sorry I didn't specify context. The ASA is setup as an SSLVPN. I want to block traffic to certain ports like FTP, NetBIOS, SMTP on the 192.168.61.0/24 inside network for the SSL VPN clients.SSL VPN User ---------Internet------ASA5505---Inter...

pattyj · 11-02-2010

Well, I did find the problem. There was a problem with the third computer I was testing with. I can in fact have 3 simultaneous users on my ASA5505 with the 25 user license. The problem was on the third computer. I am working from behind a corpor...

Member Since	‎06-14-2004 11:51 AM
Date Last Visited	‎02-05-2024 12:29 AM
Posts	35

User Statistics

User Activity

Can you add more than one built in variable in one action snmp-trap strdata statement?

EEM on Nexus 5K - only one "event syslog occurs 1" taken and 2nd "event syslog occurs 1" statement does not show

Kill a Prime job via the Prime CLI?

IOS Version Dashboard in Cisco Prime

Prime CLI Template #Interactive Mode - does it care on spacing?

Re: IOS Version Dashboard in Cisco Prime

Re: Prime CLI Template #Interactive Mode - does it care on spacing?

Re: What is required to get SNMPv3 informs to be sent? Configured but debugs showing nothing sent to NMS host.

Re: Inside interface outbound ACL applied but not blocking traff

Re: SSL VPN 25 user license - Cannot get more than 2 SSL VPN con