About BlueTongue

BlueTongue · 08-24-2014

Hello,I have a few CISCO 837, 857 and 877 routers which I wanted to reuse them by first downloading the "latest" IOS.However, I was told that this is impossible as a) CISCO no longer sells them and b) all such service contracts have expired.Can someo...

BlueTongue · 03-26-2013

Hi all,I have this 3750 stack where all ports are configured as below.The data runs on VLAN 1 and the voice runs on VLAN 100. interface FastEthernet1/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 1,100switchport mode trunk Name...

BlueTongue · 10-10-2011

Hi,I am planning to configure QOS on CISCO routers in our MPLS network whereas the switches are DELL 3548P.I am not sure if the routers and switches are compatible but when I did a "show qos' on the DELL switches, I got:console#show qosQos: basicBasi...

BlueTongue · 10-05-2011

Hi, I have one switch in a small office which I have defined 2 VLANs. One VLAN (VLAN 10) is for data and another VLAN (VLAN 20) is for voice.This small office network is connected to the headquarters network.The small office network has a DHCP serve...

BlueTongue · 03-01-2011

Hi,I am going to purchase 6 x Catalyst WS-C2960S-48FPD-L switches and make them into 2 stacks (because 4 is the maximum switches in a stack).I want to connect the 2 stacks using 10GB.What kind of transceiver and fibre cable do I need to buy in order ...

BlueTongue · 08-24-2014

Thank Sandy.I have been to the links before and it keeps asking..."Service Contract required"and I was not able to get any service contract for CISCO 837.

BlueTongue · 04-04-2013

> Your ports need to be either data/voice access ports not trunkedYes, this is what I thought.However, when I tested it again, I was surprised to see that defining the port as trunk like below works for both printer and phone (with PC piggyback)!!!!!...

BlueTongue · 03-27-2013

> I see no reason it should not work as trunk, > and prior to the switchport voice VLAN command this was the way to get IP phones working (especially non-Cisco).> interface FastEthernet1/0/1> switchport trunk encapsulation dot1q> switchport trunk all...

BlueTongue · 03-27-2013

Thanks lpassmore!> Assumption 1. PCs and printers have IP addresses in VLAN 1Yes, PCs and printers belong to the same subnet> Assumption 2. Phones have IP addresses in VLAN 100Yes, Phones belong to a different subnet> interface FastEthernet 1/0/1> sw...

BlueTongue · 03-27-2013

Good question: someone configured the switches some time ago and I just picked it up.You are right. There is no reason why it needs to be a trunk port for printers because they are not VLAN-aware devices.I was hoping that I could just use the same c...

Member Since	‎01-26-2006 11:03 PM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	26

User Statistics

User Activity

Download IOS for EOL ADSL routers

Newbie: Printer inaccessible to LAN

QOS Newbie: CISCO router and DELL switches

Is ip helper-address required in this situation?

What to connect 2 x 2960 stacks using fibre?

Thank Sandy.I have been to

Re: Newbie: Printer inaccessible to LAN

Re: Newbie: Printer inaccessible to LAN

Newbie: Printer inaccessible to LAN

Newbie: Printer inaccessible to LAN