About Peter L

Peter L · 10-18-2018

Hi Aleksandar & the rest of the xr-team I saw the Cisco live presentation BRKSPG-2904 from Barcelona this year. It was mentioned there that Flow label was going to be supported for pwhe. Has it been decided in which release this will be supported yet...

Peter L · 12-07-2016

Hi Noticed today that you have done some syntax changes between 5.2.4 and 5.3.4 when it comes to dhcp ipv4 snooping. In 5.2.4 Dhcp ipv4interface [GigabitEthernetX/X/X/X.xxxx snoop information option format-type circuit-id test123 In 5.3.4 this se...

Peter L · 06-02-2016

Hi Is there a way to show current configuration in a context in configuration mode? as an example RP/0/RSP0/CPU0:9k(config)#l2vpn bridge group L2_DCS bridge-domain 502RP/0/RSP0/CPU0:9k(config-l2vpn-bg-bd)# If i stand here the only way to see active c...

Peter L · 04-29-2016

Hi Just wondering why there isn't any input/output rate on l2transport subinterfaces. L2transport subinterface Bundle-Ether625.2204 is up, line protocol is up Interface state transitions: 1 Hardware is VLAN sub-interface(s), address is d46d.506e.03...

Peter L · 10-16-2015

HiJust wondering what the thoughts was when the show tech command was designed in IOS-XR? Opened a case yesterday and was asked to do 6 different show tech captures. It took between 30 min and 60 min for each showtech file to run. That's maybe ok whe...

Peter L · 04-05-2019

HiI know this is an old thread but saw this when searching for the same thing. Though it would be good to post an answer if someone else stumble upon this thread.You can use ip http client source-interface GigabitEthernet0To get copy http to work whe...

Peter L · 03-26-2019

HiIf i don't remember wrong you get that error when you already have created an interface (default l3) and then try to convert it to l2transport without removing the old one. Try the following and see if it's work.no interface Bundle-Ether200.500no ...

Peter L · 03-26-2019

HiYeah that will work. Just make sure that you pop tag on interface configurationSomething like this:interface TenGigE0/1/0/0.100 l2transportencapsulation dot1q 100rewrite ingress tag pop 1 symmetric!interface TenGigE0/1/0/0.200 l2transportencapsulat...

Peter L · 12-05-2018

Hi You need to add the satellite under the nv context nv satellite 100 type asr9000v secret 5 xxxxxxxxxxx description satellite connected to asr9k upgrade on-connect ! And then under the bundle-interface (this is called ICL) that is connect...

Peter L · 11-01-2018

Sorry for that Eddie. Thought that this was supported as the 880 has the sfp ports. But i guess i learned something new today :)

Member Since	‎04-05-2011 01:36 AM
Date Last Visited	‎12-15-2021 12:43 AM
Posts	82
Total Helpful Votes Received	81

User Statistics

User Activity

PWHE Flow label

Change of syntax dhcp ipv4 snooping 5.2.4/5.3.4

show active configuration in a specific context in configuration mode.

input/output rate when doing show interface on an l2transport subinterface

Whats up with show tech on ASR9K

Re: Copy HTTP VRFaware

Re: 'VLAN MA' detected the 'warning' condition 'Layer 2 subinterfaces may not be transformed into Layer 3 ones and vice versa'

Re: Local switching IOS XR - Different Subinterfaces of Same Port?

Re: ASR 9000v access switch

Re: Is NV-Cluster/Edge - still supported on the RSP880 ?