About zeeshan iqbal

zeeshan iqbal · 09-26-2015

Cisco 5508 is new Wireless LAN Controller supporting new 802.11ac Giga bit Wireless. this has been plugged into LAN port of Small-Business Security Appliance SA 520 LAN port (trunk). Default vlan 1 works fine which is for management but data vlan doe...

zeeshan iqbal · 02-18-2013

2 ASAs have a site to site tunnelASA1 local network: 172.23.10.xASA2 local network: 192.168.60.x ASA-1 has also another interface with 192.168.60.x subnet and the remote network for one of its site-to-site tunnels has the same subnet as well. NOW ASA...

zeeshan iqbal · 12-25-2012

Cisco CME 8.6 have SIP trunks connected to provider server as IP Trusted list (not as register SIP trunks) and have internal SIP devices (Apple iphone and ipad) which require registration to this cme as local extensions. Office Telepony connection to...

zeeshan iqbal · 07-29-2012

HOW to configure local and remote ID on Cisco ASA for Aggresive mode IKE ?The ID must have a '@' symbol in it as required by other peer. I coulod not have this symbol in hostname of ASA like mycisco@branch ?do i need to remove the peer IP address fro...

zeeshan iqbal · 07-04-2012

we have hub and spoke topology (multipoint VPN). one of branch site has 2 Wan links; one primary gi0/0 and one secondary dialer0. At the moment tunnel source is gi0/0 and it works fine but during automatic failover tunnel drops be...

zeeshan iqbal · 09-29-2015

Hi Gabrillo,I reset WLC, switch and Firewall to factory default and re-configured. All seems fine.Thanks for your replies and I Marked you reply as Correct answer because you were right from the start; there are no compatibility issues. and also your...

zeeshan iqbal · 09-28-2015

Thank you again for your suggestion. make sense to me. I am working on it but no joy.Could it be something to do with data vlan encryption as this is WLC 5508 and APs are 2702i?Also you mentioned to allow CAPWAP traffic through the firewall. i really...

zeeshan iqbal · 09-28-2015

Hi Gabrillo, Thanks for your reply.Yes, DATA VLAN is another VLAN that you have configured on the WLC. However DHCP is sitting on Small Business SA 520 for this data VLAN. where this DHCP should be sitting ideally? Also interesting point is WLC can p...

zeeshan iqbal · 08-21-2013

Hi Yousaf,Thank you for your suggestion and it really helped me in resolving the issue.For SIP Trunks terminating on CME, the above given command is essiential to disable the default behavior of referin to SIP proxy and now i can transfer incoming ca...

zeeshan iqbal · 08-21-2013

Hi, Thank you for your reply.Current situation:RAM: 786 MBCisco router C2811: 15.1(4) M5 (C2800NM-ADVIPSERVICESK9-M)CME Version 8.6Are you suggesting to upgrade router IOS only or CME verison as well?cheerszeeshan

Member Since	‎07-04-2012 09:26 AM
Date Last Visited	‎09-26-2018 07:38 AM
Posts	13

User Statistics

User Activity

WLC 5508 not working with Small Business security Appliance SA 520

one of the local interface has same IP subnet as of remote network for a site to site Tunnel

Cisco CME 8.6 have SIP trunks connected as IP Trusted list and have internal SIP devices

IPSec VPN on Cisco ASA as Aggressive Mode

DMVPN tunnel source for 2 WAN Links

Hi Gabrillo,I reset WLC,

Thank you again for your

Hi Gabrillo, Thanks for your

Call Transfer between SIP and SCCP on CME

Call Transfer between SIP and SCCP on CME