About rarmitage

rarmitage · 03-05-2021

When I dial directly into the Hunt Pilot I get the Initial announcement played. We I transfer in from a Call Handler the announcement does not play. Any Ideas?

rarmitage · 10-31-2018

I am trying to upgrade the rommon on a ISR4321/K9 and get the following error. TEST_NAT#upgrade rom-monitor filename flash:isr4300-rommon.162-1r.pkg allInvalid file: flash:isr4300-rommon.162-1r.pkgCisco IOS XE Software, Version 03.16.04b.S - Extend...

rarmitage · 10-23-2018

have a NIM-ES2-8-P installed in my 4321 router and I am not getting power for a Cisco 7945 IP phone. Do you have to do any special configuration on the interface port for POE

rarmitage · 02-20-2018

I have a Hunt Pilot Group set up and I trying to run reports on who in line group picked up the call. The calls work but the only place I see the call coming in the CDR is on the Hunt Pilot extension. In the destination CMR -directoryNum (finalCall...

rarmitage · 05-27-2015

Virgin Mobile Phone rings once and then goes to fast busy when caller id is enabled. Works fine when you take called id off. Other Mobile phones work fine. The call is going into an FXO port on a Cisco 2911 Version 15.2(4)M4. We are running call Cis...

rarmitage · 10-31-2018

I just had to change flash: to bootflash: and it worked

rarmitage · 10-23-2018

Thanks I thought a 110 watts was too low run a POE Module.

rarmitage · 10-23-2018

sh invNAME: "Chassis", DESCR: "Cisco ISR4321 Chassis"PID: ISR4321/K9 , VID: V04, SN: FLM2235W136 NAME: "Power Supply Module 0", DESCR: "110W AC Power Supply for Cisco ISR 4320"PID: PWR-4320-AC , VID: , SN: NAME: "Fan Tray", DESCR: "Cisco ISR4320 Fan ...

rarmitage · 10-23-2018

sh platform diagChassis type: ISR4321/K9 Slot: 0, ISR4321/K9 Running state : ok Internal state : online Internal operational state : ok Physical insert detect time : 00:00:28 (00:45:17 ago) Software declared up time : 00:01:08 (00:44:37 ago) CPLD ver...

rarmitage · 10-23-2018

NAME: "NIM subslot 0/1", DESCR: "NIM-ES2-8-P"PID: NIM-ES2-8-P , VID: V01, SN: FOC22225QUA Above is the module I thought I could get POE on the 4321. I just remember on the 2801 you had to upgrade the power supply for the extra wattage. Other then I...

Member Since	‎10-09-2007 09:41 AM
Date Last Visited	‎11-17-2023 08:39 AM
Posts	29
Total Helpful Votes Received	25

User Statistics

User Activity

Initial Announcement for Hunt pilot not playing when transferred from call handler

ISR 4321 Rommon ugrade Fails

NIM-ES2-8-P Not giving POE when installed in 4321 router

Hunt Pilot Line Group CDR Reporting

Virgin mobile phone will not connect

Re: ISR 4321 Rommon ugrade Fails

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router

Re: NIM-ES2-8-P Not giving POE when installed in 4321 router