About learner2008

learner2008 · 03-08-2013

This is a new VoIP site at Manila. The issue occured intermittenly from the day one then became hard down in two weeks. The symptom is that local users get busytone upon answering PSTN calls. I have been worked with at least three TAC Engineers and w...

learner2008 · 06-16-2011

Hi,is this command always showing the current configuration of router/switch? I have an output listed below -NAME: "2851 chassis", DESCR: "2851 chassis"PID: CISCO2851 , VID: V03 , SN: FTX1043A40YNAME: "ATM AIM 0", DESCR: "ATM AIM"PID: AIM-ATM...

learner2008 · 02-25-2011

Hi,I am new to switch and router world.One of challenging for me is to understand the meanings of IOS image and find out the right one. Can anyone provide me with documents/explanation? For example, I have a switch with boot loader only - C3560 Boot...

learner2008 · 02-20-2011

cisco 2821 gateway router with CMEWe are experiencing an issue with voicemail. the inbound calls get busytone after a few rings. Does anyone know how to reboot Unity Express module on gateway router? or any ideas of what I need to do?Thanks in advanc...

learner2008 · 10-19-2010

We are having an issue with local and mobile dialing in Argintia office. There is newly installed 2921 router with E1 R2 connection to PSTN.the symptom is that when we dial local PSTN or mobile number in digit-by-digit, call goes through. When we use...

learner2008 · 03-11-2013

the UCM trace files are attached as well. Please see 'Pub_Trace_2' and 'Sub_Trace_2'.Thanks,Jessica Wang

learner2008 · 03-11-2013

yes, i have done the changes then did a test call. the trace - 'debug_2' has been attached for your view. The H323 configuration looks like below after this change -voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow...

learner2008 · 03-08-2013

Thanks so much for reply.the running-config has been attached. Under voice service, the 'call start fast' is not present. Could you please advise how to disable it?The statement below were added by one of TAC Engineer. He also tried to enable 'Fast s...

learner2008 · 06-04-2012

Hi Anil,Thanks so much for your reply.Hi Mohammed,To answer your questions -1> ISDN switch type - Per Telco, they uses NI2 as protocol and 5ESS as switch-type. I tried both 'Primary-NI' and 'Primary-5ESS" but got same issue2> isdn incoming-voice se...

learner2008 · 06-03-2012

hi Chris,Please see the output below -"Debug ISDN q921"May 31 18:11:25.799: ISDN Se0/0/0:23 Q921: User TX -> SABMEp sapi=0 tei=0May 31 18:11:26.799: ISDN Se0/0/0:23 Q921: User TX -> SABMEp sapi=0 tei=0May 31 18:11:27.799: ISDN Se0/0/0:23 Q921: User ...

Member Since	‎10-10-2008 12:11 PM
Date Last Visited	‎09-27-2018 03:19 PM
Posts	53
Total Helpful Votes Received	8

User Statistics

User Activity

"Resource unavailable, unspecified" for PSTN inbound

Show Inventory Command

IOS image name conventions

how to reboot Unity Express Module?

Redial feature gets busy tone but call works with digit-by-digit dialing

"Resource unavailable, unspecified" for PSTN inbound

"Resource unavailable, unspecified" for PSTN inbound

"Resource unavailable, unspecified" for PSTN inbound

ISDN Layer 2 State = TEI_ASSIGNED

ISDN Layer 2 State = TEI_ASSIGNED