About KonstantinC

KonstantinC · 11-30-2021

Hello guys, Previously I had ISR 2901 router with LTE modem. Sim card worked fine. 2901#sh cellular 0/0/0 profileProfile password Encryption level: 7Profile 1 = ACTIVE* **--------PDP Type = IPv4PDP address = 10.10.10.11Access Point Name (APN) = MYAPN...

KonstantinC · 05-04-2021

Hello! I need to connect a device directly to ASR 9k router.Device doesn't support vlan tagging and is connected to Gi0/0/0/1 inetrface. Configuration is on picture below.Two ASR routers have connectivity and HSRP works fine.But there is no connectiv...

KonstantinC · 05-28-2015

Hi! There are two CSR1000V. One of them should recieve ip address through DHCP from another.R1 is dhcp client, R2 is dhcp server I see dhcp discovers on R2 and no mesages are sent:R2# show ip dhcp server statMessage RecievedDHCPDISCOVER 32DHCPREQUE...

KonstantinC · 11-11-2014

Hello Is it possible to configure l3-connected ISG dual stack on ASR1000?

KonstantinC · 07-01-2014

HelloI encountered a problem - ASR 1006 ignores shaping\policing configuration on a port-channel interfaces.If I configure: policy-map Shaping class class-default shape average 100000interface TenGigabitEthernet0/0/0 no ip address channel-group 1 mo...

KonstantinC · 11-30-2021

Ufff... sorry I forgot to configure dialer: dialer watch-list 1 delay route-check initial 60dialer watch-list 1 delay connect 60dialer watch-list 1 delay disconnect 2147483dialer-list 1 protocol ip list 1 Now all work fine

KonstantinC · 05-04-2021

Configuration is correct. It was all about misprint in the ip address.Sorry to waste your time.

KonstantinC · 05-28-2015

R2# debug ip dhcp server packetDHCP server packet debugging is on.Option 82 not presentDHCPD: Reload workspace interface GigabitEthernet3 tableid 1.DHCPD: tableid for 10.0.0.1 on GigabitEthernet3 is 1DHCPD: client's VPN is VPN1.Option 82 not presentD...

KonstantinC · 11-12-2014

I did not find any information about l3-connected dual stack configuration.. There may be two distinct sessions for one client - ipv4 and ipv6.. but this is not what I need

KonstantinC · 02-10-2014

I've found the answer to my question:http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/High_Availability.html#wp1058945"On the Cisco ASR 1006 Router, the second IOS process can run only on the standby Route Processor. Two IO...

Member Since	‎11-07-2012 10:25 PM
Date Last Visited	‎12-09-2021 06:39 PM
Posts	19
Total Helpful Votes Received	5

User Statistics

User Activity

ISR4331 LTE sim. How to get it to work?

Connectivity between untagged port and BVI on ASR9k

CSR1000V. DHCP server issue

[ASR1K] ISG Dual Stack configuration

ASR 1006 shaping\policing on port-channel interfaces

Re: ISR4331 LTE sim. How to get it to work?

Re: Connectivity between untagged port and BVI on ASR9k

R2# debug ip dhcp server

I did not find any

ASR 1006 Software Upgrade with Dual IOS Processes on a Single RP