About emiliano.eusebio

emiliano.eusebio · 01-25-2017

Hi Experts, We have a customer with a lot of ASR9010 with the V1 chassis, and they want to migrate the RSP-4G to the RSP-880, but I have a doubt about if we also must change the PEMv1 to the PEMv2 or PEMv3. I tried to search for some information abou...

emiliano.eusebio · 04-28-2014

Hi to all,I need to synchronize an ASR9K with a Symmetricom TP5000 Grand Master, for this I have a 2Mhz signal, incoming in the BITS input of the RSP440. The problem that I found is that the Sync0 input appears as "Unqualified" and I don't know how t...

emiliano.eusebio · 01-10-2014

Hi to All,I have a doubt about the possible difference between the xconnect with encapsulation default and the xconnect in port mode, is the same thing? Is one better than other? which is the correct implementation and configuration of the xconnect p...

emiliano.eusebio · 09-16-2010

Hi,Can someone explain me which is the difference in configure the conf-reg value in 0x102 or 0x2102?Thanks a LotEmiliano

emiliano.eusebio · 06-29-2009

Hi,I have a customer that have 3 routers 7600, and the behavior of mls cef is different in the 3 boxes.In one of this boxes they have one BGP full routing in ipv4 and another full BGP in one VRF, and they have this:sh mls cef summTotal routes: ...

emiliano.eusebio · 06-30-2016

Hi Xanders, thank you very much for the clarification! and thank you for be active in the forum!! Best Regards! Emiliano

emiliano.eusebio · 06-30-2016

Hi Xander, I need to know if I'll use an ASR9K as BNG (we have the BNG licenses!) and I want to use PWHE, I'll need some VRF license (iVRF or AIP)? As I know the RP don't use license for VRF. But I have some doubts about the PWHE implementation. T...

emiliano.eusebio · 10-29-2014

Hi Marek,If you want to keep the original VLAN ID, so you must to use the following configuration;!interface GigabitEthernet0/6 no ip address loopback driver negotiation auto no keepalive service instance 5 ethernet encapsulation dot1q 5 rewrite in...

emiliano.eusebio · 10-27-2014

Hi Marek, I think that you need to delimit the EFP with an encapsulation, if you want to add a full port, Port-Based EoMPLS you must do it without an EFP: ! interface GigabitEthernet0/11 description CE_facing xconnect 111.0.1.1 501 encapsulation ...

emiliano.eusebio · 05-28-2014

Hi Xander,I had some time to make additional troubleshooting:Basically the main reason why the 2m signal is not selected, is because the ANUE don't generate 2,048Khz and only generate 2,000Khz (the ANUE gives the option of generate the 2Mhz signal di...

Member Since	‎12-09-2004 06:56 AM
Date Last Visited	‎01-19-2018 12:16 AM
Posts	14

User Statistics

User Activity

RSP880 on ASR9010 V1 Chassis

ASR9K: frequency synchronization (2Mhz, BITS input)

ASR901: encapsulation default xconnect vs xconnect port mode

0x102 or 0x2102

MLS CEF behavior

Hi Xanders, thank you very

Hi Xander,

Hi Marek,If you want to keep

Hi Marek,

Hi Xander,I had some time to