Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About zimengcao
08-18-2017
zimengcao
Member since
07-30-2012
Beginner
4
Posts
0
Helpful
0
Solutions
Created by
zimengcao
in VPN and AnyConnect
in VPN and AnyConnect
05-10-2013
07:39 PM
05-10-2013
07:39 PM
Thank you very much , I think the first I need to do is just get the thread clear and then try and test on the router . Good idea for me by your mention. BR, zi
... View more
Created by
zimengcao
in VPN and AnyConnect
in VPN and AnyConnect
05-10-2013
06:51 PM
05-10-2013
06:51 PM
JouniForss ,thank you , you give me the best answer , I have searched on the website and tested on my router time and again but still failed , now I know the that only ASA can reach this goal . Thank you for giving me the post link for reference. BR, zi
... View more
Created by
zimengcao
in VPN and AnyConnect
in VPN and AnyConnect
05-10-2013
06:24 PM
05-10-2013
06:24 PM
Thank you for Jouni's reply, following is the configuration on Cisco 2800 router ,no firewall enable, : crypto isakmp policy 100 encr aes 256 authentication pre-share group 2 crypto isakmp key x.x.x address 0.0.0.0 0.0.0.0 crypto isakmp keepalive 60 ! ! crypto ipsec transform-set IPsectrans esp-3des esp-md5-hmac ! crypto dynamic-map IPsecdyn 100 set transform-set IPsectrans match address 102 ! ! crypto map IPsecmap 100 ipsec-isakmp dynamic IPsecdyn ! ! ! interface Loopback1 ip address 10.10.200.1 255.255.255.0 ! interface FastEthernet0/0 ip address 113.113.1.1 255.255.255.128 ip nat outside ip virtual-reassembly duplex auto speed auto crypto map IPsecmap ! interface FastEthernet0/1 ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly duplex auto speed auto ! ip route 0.0.0.0 0.0.0.0 113.113.1.2 ! ip http server no ip http secure-server ip nat inside source list 100 interface FastEthernet0/0 overload ! access-list 100 permit ip 192.168.1.0 0.0.0.255 any access-list 102 permit ip any 10.20.2.0 0.0.0.255
... View more
Created by
zimengcao
in VPN and AnyConnect
in VPN and AnyConnect
05-10-2013
04:31 PM
05-10-2013
04:31 PM
Hi, all, I have seen a good post in google.com about how to make all the client's traffic though IPsec tunnel then out to the Internet from the Main site,now I attach this configuration and application for discussion, and what the problem is that I am still confused with the configuration on Main site , I hope anyone who can tell me more detail and how to accomplish it. Any answer will be appreciated , thank you ! Quote : Question ? : Mine is a very simple configuration. I have 2 sites linked via an IPsec tunnel. Dallas is my Main HQ R1 and Austin R2 is my remote office. I want all traffic from Austin to route thru the tunnel up to Dallas, then out to the Internet. Dallas (Main) Lan Net is: 10.10.200.0/24 Austin (Remote) LAN Net is: 10.20.2.0/24 The Dallas (Main) site has a VPN config of: Local Net: 0.0.0.0/0 Remote Net: 10.20.2.0/24 The Austin (Remote) site has a VPN config of: 10.20.2.0/24 Remote Net: 0.0.0.0/0 The tunnel gets established just fine. From the Austin LAN clients, I can ping the router at the main site (10.10.200.1). This is how I know the tunnel is created, but I cannot ping anything beyond the router from the Austin LAN, e.g. 8.8.8.8. I'm sure it's something simple I failed to configure. Anyone have any pointers or hints? Answer: Thanks to Jimp from the other thread, I was able to see why it was not working. To fix, I had to change the Outbound NAT on the main side to Manual. Then I created a new Outbound NAT rule that included the subnet from the Austin network (10.20.2.0). Basically, I just created a copy of the default rule and changed the Source network. Once I made this change, Voila! Traffic from the remote side started heading out to the Internet. Now all traffic flows thru the Main site. It makes perfect sense why I needed to make this change, it just took a slap in the head from Jimp to point me in the right direction. My question ? The answer said "To fix, I had to change the Outbound NAT on the main side to Manual. Then I created a new Outbound NAT rule that included the subnet from the Austin network (10.20.2.0). Basically, I just created a copy of the default rule and changed the Source network." what this mean and how to do it , could anybody give me the specific configuration ? thanks a lot.
... View more
Labels:
Created by
zimengcao
in VPN and AnyConnect
05-10-2013 07:39 PM
05-10-2013 07:39 PM
Thank you very much , I think the first I need to do is just get the
thread clear and then try and t...
Created by
zimengcao
in VPN and AnyConnect
05-10-2013 06:51 PM
05-10-2013 06:51 PM
JouniForss ,thank you , you give me the best answer , I have searched on
the website and tested on m...
Created by
zimengcao
in VPN and AnyConnect
05-10-2013 06:24 PM
05-10-2013 06:24 PM
Thank you for Jouni's reply, following is the configuration on Cisco
2800 router ,no firewall enable...
Created by
zimengcao
in VPN and AnyConnect
05-10-2013 04:31 PM
05-10-2013 04:31 PM
Hi, all, I have seen a good post in google.com about how to make all the
client's traffic though IPs...
Public Statistics
| Date Registered | 07-30-2012 06:03 PM |
| Date Last Visited | 08-18-2017 04:00 AM |
| Total Messages Posted | 4 |
