About deepakkrssit

deepakkrssit · 05-21-2013

Hello Folks,I am not able to find this particular ESXi iso image on Cisco or Vmware Websites.ESXi 5.0 update 2.Can someone help with the link or details .

deepakkrssit · 10-19-2012

Hello Experts,We have a new project which is based on Flexpod design and needs a direct attach between the FI 6248 and NetAPP storage.(Without a Fabric Switch N5K or MDS)We had concern if Cisco has validated this design.Or else if there is CVD(Cis...

deepakkrssit · 10-10-2012

Hello UCS Gurus,I am setting up a new UCS lab with 1 5108 Chassis,pair of FI 6248 and FEX2104.My query about the FI 6248 is that1) I have 12 pre-licenced Unified ports on my FI 6248 and I need to configure 1-10 for Ethernet and 11th/12th for FC port....

deepakkrssit · 08-06-2012

Hello UCS Gurus,I am in middle of my UCS lab setup( Chassis 5108, pair of FIs 6248) Conncted to catalyst switches for Uplink Ethernet and MDS fabric switch to Netapp Storage.Now since Brocade dont support VSANs ,so my query is while creating Servic...

deepakkrssit · 08-06-2012

Are Service profiles in UCSM dependent on Blade Hardware? Can we assign same service profile to a B200M2,B230 M2 and a B200M3 Blade?An example: If my B200 M2 crashes because of a Hardware Failure, I replaced the same slot with a B200 M3 Blade.Then is...

deepakkrssit · 07-26-2013

Got notification this week only reagrding the power supplies for the Chassis.UCS B-Series chassis power supplies have an issue which can cause shutdown when activated in a redundancy switchover. Affected units can be identified by the version and s...

deepakkrssit · 07-22-2013

Thanks Abhinav, I forgot to share the results .....This architecture is validated now and the best part was that Zoning can be done on FI. Good to see FI working as a fabric Switch.I also validated Boot on SAN for ESX 5.0 u1 and u2.Now this looks a v...

deepakkrssit · 05-21-2013

Hello jjohnston,Yes UCSM 2.1 support direct connect FC storage on the FIs.Make sure UCSM2.o does not support that.You need to first upgrade your UCSM version from 2.0 to 2.1.Then You need to make your FC ports in FC Switch mode and create new VSANs. ...

deepakkrssit · 05-21-2013

Hello Mukesh,Hope this helps.1. Activate UCSM 2. Activate Server adapter (It will show as “Pending Next Reboot”)3. Activate server CIMC (CIMC will reboot and come up)4. Activate IOM (This will show as “Pending Next Reboot”)5. ...

deepakkrssit · 01-04-2013

Hello Abhinav,Thanks for your feedback and you were right as this id the feedback from Stoarge Team."The TX/RX signals had been inverted for the storage direct-attachment.I modified the cabling and now the link are up :"=======================So no...

Member Since	‎05-07-2012 11:34 PM
Date Last Visited	‎08-18-2017 04:00 AM
Posts	22

User Statistics

User Activity

Link of ISOs for ESXi 5.0 update 2

UCS direct attach to NetApp in Flexpod

FI 6248 Pre Licenced ports(1-12) configuration for Ethernet and FC

Cisco UCS with Brocade + NetApp

Are Service profiles in UCSM dependent on Blade Hardware? Can we assign same service profile to a B200M2,B230 M2 and a B200M3 Blade?

Re: Power state on Chassis # is redundancy-failed

UCS direct attach to NetApp in Flexpod

UCS 2.0 to 2.1 Upgrade with Direct Attached Storage

Dear Expert

UCS direct attach to NetApp in Flexpod