Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Muhammad Azhar
Stats
Member since
02-24-2011
31
Posts
11
Helpful
0
Solutions
11-12-2018
12:52 PM
Please enable logging in access control policy , i test it on FMCv 6.2.3.
... View more
09-07-2015
10:25 AM
now on Foreign controller (Cisco Controller) >show mobility summary Mobility Architecture ........................... Flat Mobility Protocol Port........................... 16666 Default Mobility Domain.......................... GH-WLC-Wifi Multicast Mode .................................. Disabled Mobility Domain ID for 802.11r................... 0x52ef Mobility Keepalive Interval...................... 10 Mobility Keepalive Count......................... 3 Mobility Group Members Configured................ 2 Mobility Control Message DSCP Value.............. 0 Controllers configured in the Mobility Group MAC Address IP Address Group Name Multicast IP Status 18:e7:28:c0:57:00 10.23.120.12 GH-WLC-Wifi 0.0.0.0 Up 74:a2:e6:c6:89:20 10.23.120.50 GH-WLC-Wifi 0.0.0.0 Control and Data Path Down (Cisco Controller) > (Cisco Controller) > (Cisco Controller) > (Cisco Controller) > now on Anchor contoller (Cisco Controller) >show mobility summary Mobility Architecture ........................... Flat Mobility Protocol Port........................... 16666 Default Mobility Domain.......................... Guest-Wifi Multicast Mode .................................. Disabled Mobility Domain ID for 802.11r................... 0x91d7 Mobility Keepalive Interval...................... 10 Mobility Keepalive Count......................... 3 Mobility Group Members Configured................ 2 Mobility Control Message DSCP Value.............. 0 Controllers configured in the Mobility Group MAC Address IP Address Group Name Multicast IP Status 18:e7:28:c0:57:00 10.23.120.12 Guest-Wifi 0.0.0.0 Control and Data Path Down 74:a2:e6:c6:89:20 10.23.120.50 Guest-Wifi 0.0.0.0 Up
... View more
Thanks for your input. I try
in Wireless and Mobility
09-07-2015
10:20 AM
09-07-2015
10:20 AM
Thanks for your input. I try to mping and eping both but no sucess , but normal ICMP work fine. should i use same mobility name for mobility group in Ancher and forign ? Also note: Currently i m using LAN two controllers in active / standby ( I configure HA setup). Please advise. Best Regards
... View more
Created by
Muhammad Azhar
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
09-07-2015
08:20 AM
09-07-2015
08:20 AM
Dear Guys, Currently i am building a WLC setup , where i setup two WLC in active / standby configuration. Currently i am using version 7.4.121.0 on all three controller. two for LAN and one is guest controller. Active / Standy work fine But i am not able to see the mobility group work as it show " Control and Data Path Down" i try to reboot the controller multiple time but still no success. Any body help will be appreciated ------------------------------------------------------------------------- LAN controller can ping to Guest controller. Following is the output from LAN controllers. For Active / Standy some output .. like Redudancy , ping and mobility summary (Cisco Controller) >show redundancy summary Redundancy Mode = SSO ENABLED Local State = ACTIVE Peer State = STANDBY HOT Unit = Primary Unit ID = 18:E7:28:C0:57:00 Redundancy State = AP SSO Mobility MAC = 18:E7:28:C0:57:00 Average Redundancy Peer Reachability Latency = 960 usecs Average Management Gateway Reachability Latency = 676 usecs Redundancy Management IP Address................. 10.23.120.13 Peer Redundancy Management IP Address............ 10.23.120.11 Redundancy Port IP Address....................... 169.254.120.13 Peer Redundancy Port IP Address.................. 169.254.120.11 Peer Service Port IP Address..................... 0.0.0.0 (Cisco Controller) >ping 10.23.120.12 Send count=3, Receive count=3 from 10.23.120.12 (Cisco Controller) >ping 10.23.120.50 Send count=3, Receive count=3 from 10.23.120.50 (Cisco Controller) > (Cisco Controller) >show mobility summary Mobility Architecture ........................... Flat Mobility Protocol Port........................... 16666 Default Mobility Domain.......................... GH-WLC-Wifi Multicast Mode .................................. Disabled Mobility Domain ID for 802.11r................... 0x52ef Mobility Keepalive Interval...................... 10 Mobility Keepalive Count......................... 3 Mobility Group Members Configured................ 2 Mobility Control Message DSCP Value.............. 0 Controllers configured in the Mobility Group MAC Address IP Address Group Name Multicast IP Status 18:e7:28:c0:57:00 10.23.120.12 GH-WLC-Wifi 0.0.0.0 Up 74:a2:e6:c6:89:20 10.23.120.50 GH-WLC-Wifi 0.0.0.0 Control and Data Path Down (Cisco Controller) > (Cisco Controller) > (Cisco Controller) > (Cisco Controller) > Guest WLC output for mobility ( note Guest controller mangment IP can able to reach LAN controller " (Cisco Controller) >show mobility summary Mobility Architecture ........................... Flat Mobility Protocol Port........................... 16666 Default Mobility Domain.......................... Guest-Wifi Multicast Mode .................................. Disabled Mobility Domain ID for 802.11r................... 0x91d7 Mobility Keepalive Interval...................... 10 Mobility Keepalive Count......................... 3 Mobility Group Members Configured................ 2 Mobility Control Message DSCP Value.............. 0 Controllers configured in the Mobility Group MAC Address IP Address Group Name Multicast IP Status 18:e7:28:c0:57:00 10.23.120.12 Guest-Wifi 0.0.0.0 Control and Data Path Down 74:a2:e6:c6:89:20 10.23.120.50 Guest-Wifi 0.0.0.0 Up (Cisco Controller) > (Cisco Controller) > (Cisco Controller) >
... View more
Created by
Muhammad Azhar
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
08-03-2015
04:41 AM
08-03-2015
04:41 AM
Dear All, In my current scenario, i have one controller ( vers 8.0) with couple of AP and is connected on network and user get authenticated by Microsoft Radius Server (NPS). I am facing issue the domain user are not able to connected WLAN , after trying to connecte WLAN they go in status of limited connection. While the user who are not part of domain ,can authenticated by domain username and can use network , without any problem. I check the certificates on domain and non domain machines , every machine have valid Certificate from DC. Can any body suggest the possible reason for this issue. Any body suggestion will be appreciated. following are some debug output for AAA. (Cisco Controller) >debug aaa events enable (Cisco Controller) > (Cisco Controller) >*Dot1x_NW_MsgTask_0: Aug 03 13:19:19.831: 74:e5:0b:af:14:48 Not sending Accounting request (0) for station 74:e5:0b:af:14:48. Accounting disabled for the WLAN *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.786: 2c:d0:5a:fc:c7:e9 Audit Session ID added to the mscb: c0a8c8320000079255bf5195 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.787: Creating audit session ID (dot1x_aaa_eapresp_supp) and Radius Request *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.787: Creating acct session ID (dot1x_aaa_eapresp_supp) and Radius Request *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.787: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.787: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.787: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.787: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.787: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 0) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:00 *radiusTransportThread: Aug 03 15:33:41.790: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.790: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.795: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.796: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.796: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.796: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.796: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 1) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:01 *radiusTransportThread: Aug 03 15:33:41.797: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.797: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.803: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.803: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.803: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.803: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.803: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 2) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:02 *radiusTransportThread: Aug 03 15:33:41.808: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.808: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.815: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.815: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.815: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.815: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.815: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 3) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:03 *radiusTransportThread: Aug 03 15:33:41.816: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.816: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.821: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.821: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.821: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.821: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.821: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 4) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:04 *radiusTransportThread: Aug 03 15:33:41.822: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.822: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.826: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.826: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.827: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.827: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.827: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 5) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:05 *radiusTransportThread: Aug 03 15:33:41.830: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.830: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.834: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.834: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.834: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.834: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.834: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 6) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:06 *radiusTransportThread: Aug 03 15:33:41.835: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.835: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.892: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.892: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.892: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.892: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.892: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 7) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:07 *radiusTransportThread: Aug 03 15:33:41.894: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.894: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.900: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.900: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.900: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.900: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.900: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 8) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:08 *radiusTransportThread: Aug 03 15:33:41.902: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.902: 2c:d0:5a:fc:c7:e9 Access-Challenge received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.912: dot1x_aaa_eapresp_supp: sending MDNS request to ISE *aaaQueueReader: Aug 03 15:33:41.913: Found a server : 192.168.1.10 from the WLAN server list of radius server index 1 *aaaQueueReader: Aug 03 15:33:41.913: Putting the quth request in qid 1, srv=index 0 *aaaQueueReader: Aug 03 15:33:41.913: 2c:d0:5a:fc:c7:e9 Sending the packet to v4 host 192.168.1.10:1812 *aaaQueueReader: Aug 03 15:33:41.913: 2c:d0:5a:fc:c7:e9 Successful transmission of Authentication Packet (id 9) to 192.168.1.10:1812 from server queue 1, proxy state 2c:d0:5a:fc:c7:e9-03:09 *radiusTransportThread: Aug 03 15:33:41.915: 1.client sockfd 26 is set. process the msg *radiusTransportThread: Aug 03 15:33:41.915: 2c:d0:5a:fc:c7:e9 Access-Accept received from RADIUS server 192.168.1.10 for mobile 2c:d0:5a:fc:c7:e9 receiveId = 3 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.915: 2c:d0:5a:fc:c7:e9 Applying new AAA override for station 2c:d0:5a:fc:c7:e9 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.915: 2c:d0:5a:fc:c7:e9 Override values for station 2c:d0:5a:fc:c7:e9 source: 4, valid bits: 0x0 qosLevel: -1, dscp: 0xffffffff, dot1pTag: 0xffffffff, sessionTimeout: -1 *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.915: 2c:d0:5a:fc:c7:e9 Override values (cont..) dataAvgC: -1, rTAvgC: -1, dataBurstC: -1, rTimeBurstC: -1 vlanIfName: '', vlanId:0, aclName: ', ipv6AclName: , avcProfileName: ' *Dot1x_NW_MsgTask_1: Aug 03 15:33:41.916: 2c:d0:5a:fc:c7:e9 Unable to apply override policy for station 2c:d0:5a:fc:c7:e9 - VapAllowRadiusOverride is FALSE. *dtlArpTask: Aug 03 15:33:41.978: 2c:d0:5a:fc:c7:e9 Not sending Accounting request (0) for station 2c:d0:5a:fc:c7:e9. Accounting disabled for the WLAN *DHCP Proxy Task: Aug 03 15:33:42.161: 2c:d0:5a:fc:c7:e9 Not sending Accounting request (0) for station 2c:d0:5a:fc:c7:e9. Accounting disabled for the WLAN
... View more
05-21-2013
01:40 PM
Hi Janesh what is that O/E term used for .. can you please explain or any one ?
... View more
Created by
Muhammad Azhar
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
05-21-2013
01:34 PM
05-21-2013
01:34 PM
Hi All , Question regarding the Guest controller ( Ancher controller). ... What license will be required to guest controller ??? Assume i have a LAN controller with a license of 100 AP , and now i am going to plan for guest user WiFi access as well but with separt Controller. Will i need guest controller with 100 AP license ??? Your quick response will be helpful for me and if possible please share the URL for reference. Thanks.
... View more
Labels:
Created by
Muhammad Azhar
in Routing
in Routing
05-02-2013
05:39 AM
05-02-2013
05:39 AM
please look at following URL. http://www.cisco.com/en/US/tech/tk583/tk372/technologies_tech_note09186a00800949c5.shtml ... QM FSM Error The IPsec L2L VPN tunnel does not come up on the PIX firewall or ASA, and the QM FSM error message appears. One possible reason is the proxy identities, such as interesting traffic, access control list (ACL) or crypto ACL, do not match on both the ends. Check the configuration on both the devices, and make sure that the crypto ACLs match. Another possible reason is mismatching of the transform set parameters. Make sure that at both ends, VPN gateways use the same transform set with the exact same parameters.
... View more
05-02-2013
05:34 AM
I have the following configuraiton on eth0... int eth0 des DSL WAN interface no ip add no ip redirects no ip unrea no ip proxy-arp no cdp enabl no ip mroute-cache pppoe enable pppoe-client dial-pool-number 1 no sh exit I have try with default configuration of eth0 as well , but interface show the same status ... .up down...
... View more
05-02-2013
05:28 AM
my configuration is mention as .... vpdn enable vpdn-group 1 request-dialin protocol pppoe exit int eth0 des DSL WAN interface no ip add no ip redirects no ip unrea no ip proxy-arp no cdp enabl no ip mroute-cache pppoe enable pppoe-client dial-pool-number 1 no sh exit int dialer 1 des DSL WAN Dialer ip add negotiated no ip unreach ip nat outside encap ppp no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enabl ip mtu 1492 ip tcp adjust-mss 1452 ppp authentication chap pap callin ppp chap hostname xxxxxx ppp chap password xxxxx ppp pap sent-username xxxxxx password xxxxx exit dialer-list 1 protocol ip permit int vlan 1 des LAN ip add 192.168.10.1 255.255.255.0 no sh exit access-list 1 permit 192.168.10.0 0.0.0.255 ip nat inside source list 1 int dialer1 overload ip classless ip route 0.0.0.0 0.0.0.0 dialer 1 I thing my service provider is providing PPOE. You can see the eth0 configuration .... If you know please help in this regard.
... View more
05-02-2013
05:07 AM
Sorry it is not relvant question regarding issue you have discussed, I have one query for you , i thing you know this , i m in process of doing internt using DSL. I have done the configuration on cisco 887VA. Router port eth0 is not comming up , it is shown as up down state .... what can be the wrong ... There are 4 LAN ports as well they come up when i connect any device. When i connect the eth0 port to any device it do not show up , what can be reason , Is this not a regualar routed prot???
... View more
04-30-2013
04:50 AM
Hi All, I have cisco router 887VA. Question is when i connect that WAN port ( eth0) with any switch or laptop/pc i do not see the port in up state. What can be the reason. I have done "no shutdown " on interface level and there is no configuration on interface except the IP address , but it show " up down "state even the port is connected to some device. ( Is the port is faulty or some other reason). As per my concept it should show up state when we connect to some device ( Like router / switch / laptop)... please look at blow link ( Table 1. Cisco 880VA Series Data Models ) ... and please let me know what is the meaning of WAN interface : Multimode VDSL2/ ADSL2 and 2+ over ISDN ( Is that can be used as regular L3/ routing port or not ) http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-613481.html Regards
... View more
Labels:
01-30-2013
01:22 AM
In the abov context all branches user internet traffic should b routed to Proxy , which is located in my LAN. if i use defult route for this on my ASA ( route inside 0.0.0.0 0.0.0.0 10.11.11.2) for all branches and then proxy again route the traffic to ASA and then internet router , which make some confusion as i already have a defult route on my ASA to internet. I try it on GNS3 , but still have confusion regarding defult routes for internet.
... View more
01-30-2013
01:10 AM
Thanks Andi, I have some routing issue at my CO ASA. Attach is Topology diagram and configuration., I have routing issue at my ASA. Thanks
... View more
04-14-2019
Dear, I did one migration from asa 8.2 to FTD.I will suggest to upgrade
to 8.4 or higher , after thi...
Created by
Muhammad Azhar
in Identity Services Engine (ISE)
02-24-2019
02-24-2019
Thanks for your replay.I will look into the document related to threat
containment , do you have any...
Created by
Muhammad Azhar
in Identity Services Engine (ISE)
02-24-2019
02-24-2019
Thanks Mohamad for the reply.What about the FMC use case ? as per my
understanding user who trigger ...
Created by
Muhammad Azhar
in Identity Services Engine (ISE)
02-24-2019
02-24-2019
Dear Experts, I am going to integrate Pxgrid in distributed environment.
I have few points to clarif...
Created by
Muhammad Azhar
in Identity Services Engine (ISE)
02-12-2019
02-12-2019
Dear ISE experts, I am currently running a distributed ISE setup where i
have dedicated PANs,MNTs an...
Created by
Muhammad Azhar
in Identity Services Engine (ISE)
01-25-2018
01-25-2018
I found the same problem after I upgrading from 2.0.0 to 2.3 ( ISE index
engine not running ). By ad...
09-07-2015
now on Foreign controller (Cisco Controller) >show mobility
summaryMobility Architecture ..............
09-07-2015
Thanks for your input. I try to mping and eping both but no sucess , but
normal ICMP work fine.shoul...
09-07-2015
Dear Guys, Currently i am building a WLC setup , where i setup two WLC
in active / standby configura...
Created by
Muhammad Azhar
in Other Wireless - Mobility Subjects
08-03-2015
08-03-2015
Dear All, In my current scenario, i have one controller ( vers 8.0) with
couple of AP and is connect...
Created by
Muhammad Azhar
in Other Wireless - Mobility Subjects
05-21-2013
05-21-2013
Hi All , Question regarding the Guest controller ( Ancher controller).
... What license will be requ...
Created by
Muhammad Azhar
in Routing
05-02-2013
05-02-2013
please look at following
URL.http://www.cisco.com/en/US/tech/tk583/tk372/technologies_tech_note09186...
Public Statistics
| Date Registered | 02-24-2011 04:10 AM |
| Date Last Visited | 12-26-2019 02:52 AM |
| Total Messages Posted | 31 |
| Total Helpful Votes Received | 11 |
