1) Do Cisco 2960 X or XR supports SCEP ?
2) Do Cisco 2960 X or XR supports KMIP (Key Management Interoperability Protocol) ?
3) Do cisco support the below SCEP services ?
Get CA certificates
Certificate enrollment
Certficate poll - CertPoll (GetCertInitial)
Get next ca certificates
Get CA capabilities
Certifictate renewal
Certificate query
CRL query
... View more
Hi Thanks for your help, Will the below work properly as expected in cisco 2960 stack switch? Please reply ? ! config t ip igmp snooping vlan <> immediate-leave ip igmp snooping querier ip igmp snooping querier timeout expiry <60-300 Secs> ip igmp snooping tcn flood query count 2 (default) ip igmp snooping tcn query solicit end ! conf t interface Vlan<> ip pim sparse-dense-mode end !
... View more
1)To enable multicast routing in cisco2960S lan switch 2)One of the cisco2960S interfaces will be connected to Paging gateway with Static IP. 3)Another interface will be connected to a IP Speaker 4)We already have a voice vlan SVI in cisco2960S lan switch. 5)The aim is to enable multicast routing between Speaker and the paging gateway thorugh the same voice vlan (within same cisco2960S lan switch) 6)Configuration needed to execute the above. Please help
... View more
1)I have two service providers. 2)I want Meraki MX80 to use the above two service providers ISPs for redundancy. 3)I have LAN segment which is done using WS-C3750G-12S-SD as L3 and 2960 switches as L2 connected to L3. 4)So Meraki MX80 will connect to WS-C3750G-12S-SD (L3) to 2960 switch (L2). 5)Overall a site to site VPN to be made with Meraki peers cloud. 6)Need complete planning,design and configuration. Could some one please help me on this.
... View more
Hi Please find the below the ACLs, would like to know the exact difference between the two ACLs. permit tcp any gt 1023 A.B.C.3D/32 eq 80 permit tcp any eq 80 A.B.C.3D/32 gt 1023 TcpEstablished Please help
... View more
Hi Paolo *I am not a cisco parner I have done this design for learning purpose. I need some configurations for the mentioned scenario. Kindly help
... View more
Hi All, Please find the attached my project scenario. Could any one please let me whether it is possible to do or not. The Requirements are given below according to the attchment. Requirements: Phone Functionality DIAL PLAN: (8 DIGITS) XXXX YYYY , where XXXX (4 digits) Site code and YYYY (4 Digits) Specific Phone number. 1) Phone must have 8 - digit dialing facility. 2) Phones must be capable of interacting within site A as well as with site B and vice-versa. 3) Within site dialing phone must use only last 4 digit dialing, to other site it should use complete 8 digits. 4) Phones must be capable of dialing external mobile or other PSTN numbers to external world by pressing specific number 9 and followed by mobile or any PSTN number. 5) Any Call transfer must happen within site as well as with other site also. PC Functionality 1) Any PC from either sites must be able to access both official mail server and web server. 2) In addition to both official mail server and web server services , any PC must be able to access internet as well. Could any one please let me whether it is possible to do or not. Thanks and regards Jegan S
... View more
Hi Lets consider a layer 2 switch. Just see below configuration for an example... ! vlan 3 name williams ! vlan 4 name sam ! vlan 12 name harris ! vlan 107 name brucewilllis ! vlan 150 name harrisonford ! vlan 151 name willsmith ! spanning-tree mst configuration name config1 revision 1 instance 1 vlan 1-100 instance 2 vlan 101-200 ! ! interface GigabitEthernet1/1 switchport trunk native vlan 12 switchport trunk allowed vlan 3-20,100-200 switchport mode trunk ! Note: While making trunking in the interface please notice the vlan ranges 3-20,100-200. Created vlans are only 3,4,12,107,150,151. Question: *The vlan ranges (3-20,100-200) mentioned in trunked interface cover non-created vlan ranges. My question is mentioning in trunk interface with vlan ranges 3-20,100-200 numerically which are not created globally will cause any traffic related issues ????? , such as broadcast or others if any ?????, if it causes any issues,what will be the cause if it doesnt cause any issue - why it is so.... Anyone kindly clarify me on this Thanks Jegan
... View more
Hi Could any one please let me know what is the actual function of the switchport command "flowcontrol receive on/off/desired" Thanks and regards Jegan jesri@outlook.com
... View more
hi Please find the attached Can any one please tell me which is the bootdisk: or sup-bootdisk: in RSP-720-3C-GE ????? when the RSP card boots for the first time.Because you see in the attached picture there are two 512 MB memories in two different locations in a RSP card.Which is going to be the bootdisk: when the card boots for the first time. Thank you
... View more
Hi Cisco Representatives, Example : police cir <30000000> bc <51250> be <51250> conform-action <transmit /drop> exceed-action <transmit /drop> violate-action <transmit/drop> Please find the above example, I wanted to know and understand in detail what will be the impact on packets if the above policy map is applied in 6500 serires switch in its control plane? The mentioned parameters are just for an example.....
... View more