About rogelioalvez

rogelioalvez · 09-25-2023

Hello team:Let us suppose that I add a new policy map and apply it as a service policy to an interface. I am worried about the policies I had before adding the new policy.¿Will the router preserve the IDs of the other policy maps and service policies...

rogelioalvez · 08-26-2021

Hello team:My Nexus9300 cluster is composed of NX1 and NX2. NX1 and NX2 are linked with a vPC link between them. A shared portchannel between NX1 and NX2 links my cluster to a downstream "dual homed" router (one 10GE link in each NX device)For a spec...

rogelioalvez · 04-06-2020

Hello team: I have the following output in my Cisco router to the "show ip bgp 172.25.159.140 255.255.255.252" command: LASBRUOL1001-1#show ip bgp 172.25.159.140 255.255.255.252BGP routing table entry for 172.25.159.140/30, version 1073122Paths: (2 a...

rogelioalvez · 03-25-2020

Hello team:I want to apply a basic output policy to a tunnel (GRE) interface, like the following:policy-map QOS-WAN-CHILDclass voicepriority percent 10 policy-map QOS-WANclass class-defaultshape average 3000000service-policy QOS-WAN-CHILD! But when I...

rogelioalvez · 01-29-2016

Hello team: We have a 2x10GE (layer3) portchannel established between a ASR1006 and a CAT4900M. The 2x10GE ports on the CAT4900M belong to a 8x10GE(2:1) card. Traffic from servers connected to the ASR1006 router down to clients behind the CAT4900 o...

rogelioalvez · 08-26-2021

Hello Giuseppe!!!I suspected it once I saw it working that way, and your answer confirms me that this is an expected behavior as I imagined. I would have like to start a parallel layer3 interface in NX2 to circumvent the problem, but the reason why I...

rogelioalvez · 04-06-2020

Thanks for clearing this up! Best regards, Rogelio

rogelioalvez · 03-25-2020

You were right! I executed these same commands on another router model (it was easier than an IOS upgrade on the original router) and everything worked perfectly. Thanks! class-map match-all voicematch access-group name voice!!policy-map QOS-WAN-CHIL...

rogelioalvez · 03-25-2020

Hello Cristian:I will look for a different version and let you know what happened. Thanks!

rogelioalvez · 01-29-2016

Hi Jon: The remaining 10GE ports on both sides are idle. And there are many high-end servers connected to the ASR1006 and at least 50,000 clients downstream of the CAT4900M. The portchannel balancing algorithm is the default one. Next week we will te...

Member Since	‎01-13-2005 12:43 AM
Date Last Visited	‎09-27-2023 12:02 AM
Posts	160
Total Helpful Votes Received	10

User Statistics

User Activity

Cisco QOS MIB. ¿Could object IDs change when a new policy is added?

Nexus9K cluster doesn´t balance outgoing traffic on shared portchannel

Meaning of the output in the "show ip bgp <prefix> <mask>" command

Nested output service-policy on tunnel (GRE) interface

2x10GE Portchannel on a CAT4900M with 8x10GE (2:1) card does not exceed 10GE of througput

Re: Nexus9K cluster doesn´t balance outgoing traffic on shared portcha

Re: Meaning of the output in the "show ip bgp <prefix> <mask>" command

Re: Nested output service-policy on tunnel (GRE) interface

Re: Nested output service-policy on tunnel (GRE) interface

Hi Jon: