Hi All I have made a routed port on 3560G Switch and defined a pool 172.28.4.62 255.255.255.192 and connected to E1 converter RAD (4E1 to 4 FE) the E1 media is through Microwave on the other end same E1 converter is connected through layer 2 switch and defined a pool as of routed port configured in 3560G switch. The port is generating lot of giants and after a while it also distrubs other routes ( Port1 to Port 16), configured with Vlan11 and port 22 as routed port. I have checked the routed port through wireshark the maximum frame size is 1514 and configured the MTU to 1514, giants are not showing any more but after 10 to 12 hours switch gets hang. Either to shut the port or to reload the switch to get switch and other layer routes to be normal. I have checked speed and duplex settings same as E1 converter. Full duplex. 100 Speed. Can you please guide why switch is not behaving normal. If i shutdown the routed port it is normal. 1. interface GigabitEthernet0/22 no switchport ip address 172.28.4.62 255.255.255.192 flowcontrol receive on end 2. #sh int g0/22 GigabitEthernet0/22 is up, line protocol is up (connected)   Hardware is Gigabit Ethernet, address is f025.7292.3bc3 (bia f025.7292.3bc3)   Internet address is 172.28.4.62/26   MTU 1514 bytes, BW 100000 Kbit/sec, DLY 100 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation ARPA, loopback not set   Keepalive set (10 sec)   Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX   input flow-control is on, output flow-control is unsupported   ARP type: ARPA, ARP Timeout 04:00:00   Last input 00:00:00, output 00:00:00, output hang never   Last clearing of "show interface" counters 08:12:58   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/40 (size/max)   5 minute input rate 32000 bits/sec, 37 packets/sec   5 minute output rate 29000 bits/sec, 30 packets/sec      1511472 packets input, 193066909 bytes, 0 no buffer      Received 329372 broadcasts (0 IP multicasts)      0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored      0 watchdog, 315319 multicast, 0 pause input      0 input packets with dribble condition detected      1388683 packets output, 204952330 bytes, 0 underruns      0 output errors, 0 collisions, 1 interface resets      0 unknown protocol drops      0 babbles, 0 late collision, 0 deferred      0 lost carrier, 0 no carrier, 0 pause output      0 output buffer failures, 0 output buffers swapped out 3 #sh controllers ethernet-controller g0/22      Transmit GigabitEthernet0/22             Receive     208662623 Bytes                        196571703 Bytes       1395739 Unicast frames                 1201317 Unicast frames         16539 Multicast frames                320932 Multicast frames          2139 Broadcast frames                 14295 Broadcast frames             0 Too old frames               153120428 Unicast bytes             0 Deferred frames               42497542 Multicast bytes             0 MTU exceeded frames             952215 Broadcast bytes             0 1 collision frames                   0 Alignment errors             0 2 collision frames                   2 FCS errors             0 3 collision frames                   0 Oversize frames             0 4 collision frames                   0 Undersize frames             0 5 collision frames                   0 Collision fragments             0 6 collision frames             0 7 collision frames               23168 Minimum size frames             0 8 collision frames             1386857 65 to 127 byte frames             0 9 collision frames               71215 128 to 255 byte frames             0 10 collision frames              12671 256 to 511 byte frames             0 11 collision frames               7251 512 to 1023 byte frames             0 12 collision frames              35355 1024 to 1518 byte frames             0 13 collision frames                  0 Overrun frames             0 14 collision frames                  0 Pause frames             0 15 collision frames             0 Excessive collisions                 0 Symbol error frames             0 Late collisions                      0 Invalid frames, too large             0 VLAN discard frames                 29 Valid frames, too large             0 Excess defer frames                  0 Invalid frames, too small         68034 64 byte frames                       0 Valid frames, too small       1167217 127 byte frames        116592 255 byte frames                      0 Too old frames         10709 511 byte frames                      0 Valid oversize frames          4070 1023 byte frames                     0 System FCS error frames         47795 1518 byte frames                     0 RxPortFifoFull drop frame             0 Too large frames             0 Good (1 coll) frames             0 Good (>1 coll) frames ... View more

I have a following setup and call the from 650 number gets block fine but I try to add another voice translation rule 8888 that number doesn't get blocked. , can someone help me, what am  I missing ? Thanks voice translation-rule 1 rule 2 /^9\(.*\)/ /\1/ ! voice translation-rule 10 rule 1 /^312..\(.....\)/ /\1/ ! voice translation-rule 4321 rule 1 reject /6506914925/ ! ! voice translation-profile BLOCK translate calling 4321 ! voice translation-profile inbound translate called 10 ! voice translation-profile to_PSTN translate called 1 voice translation-profile BLOCK translate calling 4321 voice translation-rule 8888 rule 1 reject /8887309578/ voice translation-profile BLOCK_NUMBER translate calling 8888 ... View more

Is is possible to do bulk Subscribe/Unsunscribe  for given device pool instead of going to each phone 1 by one. I have look under BAT and couldn't find anything under updates phones field. Attach is the screen shot . Thanks ... View more

Hello, I was wondering if there is way to do a bulk update/modify for Enable Extension Mobility under Extension Information for phones. Basically there are some users which have the profile selected but we want to edit this in bulk and select " Use Current Device Settings" I am attaching a screen shot. Any help would highly appreciated. ... View more