Hi there, I´m having trouble connecting to the internet with the 877 router; I have tried several different configurations, but I always fail to connect. The Telecom said that the line is Ok, and in fact I´ m able to connect through the old Alice modem I have, even with a good bandwidth (6.5 Mbps in download). But when I try to use the 877, it fails. I was wondering whether it has to do with the attenuation: usually it is around 12 dB, as shown here below. But in my case it´s around 32dB. Can this be the reason ? or do I have to did deeper in my config file ? router#sh dsl int      ATM0 Alcatel 20190 chipset information                 ATU-R (DS)                      ATU-C (US) Modem Status:    Showtime (DMTDSL_SHOWTIME) DSL Mode:        ITU G.992.1 (G.DMT) Annex A ITU STD NUM:     0x03                            0x1 Vendor ID:       'STMI'                          'TSTC' Vendor Specific: 0x0000                          0x0002 Vendor Country:  0x0F                            0xB5 Capacity Used:   100%                            60% Noise Margin:    11.5 dB                         23.0 dB Output Power:    14.5 dBm                        13.0 dBm Attenuation:     12.0 dB                          3.0 dB Defect Status:   None                            None                        Last Fail Code:  None Watchdog Counter: 0xF5 Watchdog Resets: 0 Selftest Result: 0x00 Subfunction:     0x00 Interrupts:      8093 (0 spurious) PHY Access Err:  0 Activations:     2 LED Status:      ON LED On Time:     100 LED Off Time:    100 Init FW:         init_AMR-2.6.004.bin Operation FW:    AMR-2.6.004.bin FW Version:      2.6.4                  Interleave             Fast    Interleave              Fast Speed (kbps):          6336                0           480                 0 Cells:               126700                0         14300                 0 Reed-Solomon EC:          0                0             0                 0 CRC Errors:               0                0             0                 0 Header Errors:            0                0             0                 0 Total BER:                0E-0           0E-0Leakage Avarage BER:         0E-0           0E-0 LOM Monitoring : Disabled DMT Bits Per Bin 000: 0 0 0 0 0 0 0 2 3 5 5 6 7 7 7 7 010: 7 7 7 7 7 7 7 6 6 6 6 5 4 3 2 0 020: 0 0 0 0 0 A A A B A A A A A A B 030: A A A A A A A A A A A A A A A A 040: 0 9 A 9 A 9 9 9 9 9 9 9 9 9 9 9 050: 9 9 9 9 9 9 9 9 9 9 8 9 9 9 9 9 060: 9 9 9 9 9 9 9 8 9 9 9 9 8 8 9 8 070: 9 9 8 2 8 8 8 8 8 8 8 8 8 8 8 8 080: 8 8 8 8 7 8 8 8 7 8 8 8 8 8 7 7 090: 8 7 7 8 8 7 7 7 7 8 8 7 7 7 7 8 0A0: 7 7 7 8 7 7 7 8 8 7 7 7 7 7 7 7 0B0: 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 0C0: 7 7 7 6 7 7 7 7 6 7 6 7 7 7 7 7 0D0: 7 7 7 6 6 6 6 7 6 6 6 6 6 6 6 6 0E0: 6 6 6 6 6 6 6 6 7 6 7 6 6 6 6 6 0F0: 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 DSL: Training log buffer capability is not enabled The above output was taken from a 877 of a friend of my, who has the same contract with the Telecom. Thanks or any comment. ... View more

Hi folks, the link to the Triple Combo GUI tool to analyze CUCM trace files appears to be broken: www.employees.org/~tiryaki/tc any idea where the tool is gone or with whaht was is replaced? thanks best wishes Lucio ... View more

About Change notification settings: there is a bit of confusion in this forum, I think; there are posts which regard only the Jabber Video enterprise edition, but then when somebody asks for help about that version, they say the forum is only for the free edition. Anyway, I have a problem with both versions. There is no status notification nor status change option in the free edition; however, I have seen that the Hide system tray notification does not work in either version (neither the free version, nor the enterprise version), in fact, the Jabber Video icon with the green ball on it is always there, no matter whether I flag the option or not, no matter whether I use the free edition or the enterprise edition. Regarding the "Mute when busy" option, I think if there is no status in the free edition, it should be taken out, because it's equivalent to "mute when in a call". Or am I mistaken ? Can anybody test this and let me know? thanks Lucio ... View more

I have a question about the presence status of the Favorites in Jabber Video verison 4.6.3. I am now registered on a VCS Expressway and my favorites are in the LAN and registered on the VCS Control. I see them on the VCS Control, so I know they are online, like the MCU which always online. However I get "offline" in favorites list. I get Online if I add myself in the list and also I get Online for another Jabber Video which is also registered on the Expressway because he's also outside the LAN. When I am inside the LAN the status is always OK. It seems from some posts it has to do with authentication settings in the subzones, but I could not figure out whether I shoud put "treat as authenticated" or "do not check credentials" and where exactly (whether in the default subzone or traversal subzone and the vcse and/or the vcsc). Can someone please shed some light on this? thanks a lot ... View more

Hi there, I have a normal  Jabber Video installed on a Windows PC and logged into a private network with VCS Control and Expressway, TMS and MCU. The Jabber is registered on the VCS Expressway, because I'm outside of the private network. I then have a Jabber "cloud" and I call the normal Jabber: I see there is the lock with the red stripe and there is nothing under Encryption in the call information. However, there is encryption on the normal Jabber: here I can see the lock without red stripe and I see AES under Encryption in the call information. In the VCS Control and Expressway, I have set all SIP parameters to TLS 5061 and Encryption Best Effort for the Subzones. However when I call the other way around, i.e. from the normal Jabber to the Cloud Jabber, there is encryption on both sides. I have also verified that a call between 2 cloud Jabbers is always encrypted. In fact, it was "Auto" instead of "Best Effort": with "Best Effort" I was hoping to see encryption on both sides, no matter which way the call is going. Any clue? does it have to do withe my search rules on the subzones? The call is always traversal. Does it have to do with the firewall? Thanks Lucio ... View more

          I don't seem to be able to update my favorites list in the Jabber Video cloud client. I add a favorite, then sign out; then I sign in again and the favorite is gone. If I add more then one at a time, the outcome is the same: when sign in again they are all gone. I just have 3 favorites which were probabably the first registered when I used the client for the first time? is 3 the limit? where is it documented? thanks! regards Lucio   ... View more