Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Alex Pfeil
Online
Alex Pfeil
Member since
01-08-2008
Contributor
07-10-2019
02:05 PM
Did you delete the new IOS from flash? Verify that the old IOS is booting? Just making sure.
... View more
07-10-2019
11:33 AM
You can do it from the 1111 SSH CLI. You can do it by AP or all of them per below example. >config ap led-state disable all
... View more
07-10-2019
10:23 AM
This could be a bug, but I did not find one. I would try downgrading the switch to the next version below.
... View more
07-10-2019
10:16 AM
Is it possible to turn off the status lights on wireless access points that are connected to the 1111 WLAN controller? I was looking for the option, but I do not see it listed. Thanks, Alex
... View more
Labels:
05-31-2019
05:41 AM
Here is a link to a document showing the configuration. https://www.cisco.com/c/en/us/td/docs/security/asa/asa82/configuration/guide/config/ha_active_standby.pdf Here is a configuration example. Primary - ASA failover failover lan unit primary failover lan interface Failover Ethernet1/8 failover link Failover Ethernet1/8 failover interface ip Failover 192.168.1.1 255.255.255.252 standby 192.168.1.2 Secondary - ASA failover failover lan unit secondary failover lan interface Failover Ethernet1/8 failover link Failover Ethernet1/8 failover interface ip Failover 192.168.1.1 255.255.255.252 standby 192.168.1.2 Can you provide your configuration?
... View more
05-22-2019
01:06 PM
I currently use FlexConnect to have one SSID local and another SSID centrally switched. This is FlexConnect. FlexConnect Split-tunneling would be having one SSID with some of the traffic centrally switched and some of the traffic switched locally. If you are already doing this, then you are doing FlexConnect Split-tunneling. Please mark helpful posts.
... View more
05-22-2019
03:57 AM
FlexConnect is used to allow an SSID to be locally switched instead of tunneled back to the WLAN controller. It is also possible to have some SSIDs locally switched, while having other SSIDs tunneled back to the controller. The purpose of a split-tunnel would be to have some traffic locally switched, while having other traffic tunneled back to the controller. The idea is to save bandwidth by keeping local traffic, local. Here is a good reference on the forum. https://community.cisco.com/t5/forums/replypage/board-id/5956-discussions-getting-started-wireles/message-id/109117
... View more
05-21-2019
05:45 AM
I agree with the above post. The server will fail to local if the AAA server is not reachable. Examples are, the server is down or an ACL is blocking the request.
... View more
Created by
Alex Pfeil
in Policy and Access
in Policy and Access
05-21-2019
05:18 AM
05-21-2019
05:18 AM
That is exactly what I was looking for, thanks!
... View more
05-20-2019
11:12 AM
You are going to have to upgrade the software. The best bet is to place a ticket with TAC, and get them to give you a specific version of software to run. They should be able to suggest the most stable version.
... View more
Created by
Alex Pfeil
in Policy and Access
in Policy and Access
05-14-2019
05:40 AM
05-14-2019
05:40 AM
In my opinion, it would make sense to be able to see a report of every device that is currently using a Plus or APEX license.
... View more
Created by
Alex Pfeil
in Policy and Access
in Policy and Access
05-13-2019
11:08 AM
05-13-2019
11:08 AM
We are running ISE 2.4 patch 5. A few weeks ago, ISE started reporting that we were using over 300 more licenses than we have. Is there a way to see all the devices using a Plus license in ISE?
... View more
Labels:
05-06-2019
05:12 AM
I had converted an LWAPP to an autonomous AP. I was then able to telnet into the AP. I thought the username and password would stay the same, but it resets to the default. I was glad to come across this info. The telnet username and password was Cisco after the conversion. Thanks!
... View more
Created by
Alex Pfeil
in Networking Documents
10-20-2018 09:28 AM
10-20-2018 09:28 AM
Thanks for sharing. It seems another solution would be to change the
console application to match 38...
Created by
Alex Pfeil
in Wireless - Mobility Documents
06-20-2018 01:07 PM
06-20-2018 01:07 PM
This is a good reference for 802.11ac and the equation above. X = MCS
(0-9), Y=Spatial Streams, and ...
Created by
Alex Pfeil
in Wireless - Mobility Documents
06-20-2018 12:49 PM
06-20-2018 12:49 PM
Is there a table that converts these numbers to actual bandwidth? 6.0,
9.0, 12.0, 18.0, 24.0, 36.0, ...
Created by
Alex Pfeil
in Security Documents
06-05-2018 03:23 AM
06-05-2018 03:23 AM
I was hoping you could answer a question. 1. Is there a roadmap for how
long this will be supported?...
Created by
Alex Pfeil
in Wireless - Mobility Documents
03-12-2015 01:07 PM
03-12-2015 01:07 PM
I had a switch with power over Ethernet. I just put my computer and the
access point in a local VLAN...
Public Statistics
| Date Registered | 01-08-2008 12:55 PM |
| Date Last Visited | 07-17-2019 02:07 PM |
| Total Messages Posted | 543 |
| Total Helpful Votes Received | 381 |
.jpg "VIP Engager"){kind=icon}
Helpful Votes From
