About dylan.ebner

dylan.ebner · 01-11-2022

Is it possible to set some of our remote users jabber to bypass our expressway servers and connect directly to our CUCM and CUP servers like they were onprem? Our remote works all have vpn connections that could be used to connect jabber to CUCM. We ...

dylan.ebner · 01-18-2021

I have two ASR routers that handle my internet traffic. Each has one ISP (Comcast and Lumen). For some reason, the router I have connected to Lumen is adding a metric of 7800000 to all the routes it learns from Lumen. I have a fairly straight forward...

dylan.ebner · 11-12-2020

This may not be possible, but here's hoping. My VMware environment is 100% Cisco UCS B servers. I had an incident recently where our ESXi host servers became disconnected from our vCenter Server. Now per VMware support we need to shutdown the guest V...

802.1x and LDAP User Authentication · 11-15-2017

I want to migrate our business office from a WPA2/PSK wireless environment to using LDAP to control authentication. I found this config example which looks very neat and tidy: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan...

dylan.ebner · 07-19-2017

Hello- Today while performing an upgrade from 2.2(6e) to 3.1(3b) we had a major outage during the reboot of FI-B. The outage cleared after the 10 or so minutes it took for FI-B to restart. At first, I thought we maybe had some of our servers config...

dylan.ebner · 01-12-2022

Hi Jamie and Roger- I built a new vpn group today that does not use split tunnelling. When I connect that vpn and try to log into jabber I get a "Cannot communicate with the server." When I look at my firewall logs it looks like Jabber is still tryin...

dylan.ebner · 01-19-2021

Hi Giuseppe-Thanks for the reply. That is what I suspected, but Lumen said they were not setting the MED. The two ISPs do not have an agreement between them. Is their anyway I can prove to tech support at lumen that they are setting the MED?Thanks

dylan.ebner · 01-18-2021

could you explain "check the IGP in router originate it and find the cost of this route" a little more? The example I posted came from the router that has the high metric. My other ASR doesn't do the same thing. It always shows it's metrics at 0.

dylan.ebner · 11-12-2020

Hi BB- The FIC is the layer 2 device and I was looking for the command to get the MAC address table out of the FICs. I found it by connecting to the local-mgmt of the FIC and then I could run a show mac-address-table.

Re: 802.1x and LDAP User Authentication · 11-15-2017

Hi Flavio-This is the same example I was refrencing with my question. This doesn't work for us because of it's requirement to have all the users contained in an OU on the AD. We have our users spread out over dozens of OUs.

Member Since	‎04-28-2006 01:46 PM
Date Last Visited	‎11-13-2023 10:05 AM
Posts	81
Total Helpful Votes Received	5

User Statistics

User Activity

Can you set Jabber to bypass expressway and connect local?

ASR BGP session adding metric of 7800000 to all routes

Find MAC address for lost VMs

802.1x and LDAP User Authentication

UCS upgrade from 2.2(6e) to 3.1(3b) caused major outage during FI-B reboot

Re: Can you set Jabber to bypass expressway and connect local?

Re: ASR BGP session adding metric of 7800000 to all routes

Re: ASR BGP session adding metric of 7800000 to all routes

Re: Find MAC address for lost VMs

Re: 802.1x and LDAP User Authentication