About networklal

networklal · 12-11-2012

I recently did the following configuration changes on my ASA through ASDM. The changes were the following:Added a new service policy to the ASA inside interface to do some traffic policing. Also put the global policy rules in the inside policy.The bo...

networklal · 12-14-2011

Hi ALL,In our setup we have WiSM modules installed on cisco 6506-E, ACS 5.3 virtual appliance.We are trying to implement EAP-FAST for our Wireless using WPA/WPA2 802.1x on the WLC side.I have followed the instructions in the following document step-b...

networklal · 11-27-2011

When I try to Launch Topology Services from windows 7 client I am getting the following error message:Cannot connect to ANIServer: ANIServer7.0-CCADLMS001Attached is the screenshot for reference. Also attaching the SC QUERY and SYSTEMINFO files.I hav...

networklal · 04-04-2009

OLD Setup:The old router with one Fa0/0 interface is connected to a switch. There are two subinterfaces made on the routers fa0/0 interface which have the following configuration:interface FastEthernet0/0 description Connected to hub no ip address no...

networklal · 12-29-2008

Hi,I am trying to add devices (1 4506E and 2960G)to RME in CWSNMS both through the Admin->Essentials->Inventory->Add Devices and by adding it to Whats Up Gold and then exporting it to Essentials. But both the time I can see the devices in the invento...

networklal · 12-12-2012

Hi Jouni,Thanks for the reply. I am really not sure about the significance of the last digit. But we upgraded the ASA some time back from 8.4.(3)8 to 8.4(4)1 to mitigate some security vulnerabilites released by cisco at that time.Regards

networklal · 12-12-2012

Found the following from cisco website http://www.cisco.com/en/US/products/ps6121/products_tech_note09186a0080aaeff5.shtml#prblm14Problem: ASA network objects get deleted when using ASDM version 6.4.5 While editing an existing network object using AS...

networklal · 12-12-2012

Hi Jouniforss,Thanks for the reply. I already have this feature enabled. That is how I posted the commands sent by ASDM in my 1st post. access-list inside_mpc line 1 extended permit ip object Guest.Wireless any access-list inside_mpc line ...

networklal · 12-11-2012

Hi Jcarvaja,Thanks for your interest.Actually most of the nat statements removed included general nat statements, nat object rule both static and dynamic having nothing to do with the inside interface at all. lines removed were independent of the ins...

networklal · 12-11-2012

In the above I would like to add that the restore too was done using ASDM.

Member Since	‎06-18-2005 09:25 AM
Date Last Visited	‎04-03-2018 04:29 AM
Posts	15

User Statistics

User Activity

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1 model 5550

EAP-FAST with ACS 5.3 and WiSM | 5411 EAP session timed out

Unable to launch Topology Services in LMS 4.1

Only ping works when router is replaced

Cisco Works Small Network Management Solution CWSNMS

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

Re: ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1