Cisco Community
English
Register
Great changes are coming to Cisco Community in July. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
networklal
‎04-03-2018

Beginner
Recent Badges
Awards
Recent Badges
See all
5 Replies
Stats
Member since ‎06-18-2005
15
Posts
0
Helpful
0
Solutions

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

Created by in Network Security
12-12-2012
12-12-2012
Hi Jouni,Thanks for the reply. I am really not sure about the significance of the last digit. But we...

Re: ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(

Created by in Network Security
12-12-2012
12-12-2012
Found the following from cisco website http://www.cisco.com/en/US/products/ps6121/products_tech_note...

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

Created by in Network Security
12-12-2012
12-12-2012
Hi Jouniforss,Thanks for the reply. I already have this feature enabled. That is how I posted the co...

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

Created by in Network Security
12-11-2012
12-11-2012
Hi Jcarvaja,Thanks for your interest.Actually most of the nat statements removed included general na...

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1

Created by in Network Security
12-11-2012
12-11-2012
In the above I would like to add that the restore too was done using ASDM.

ASDM 6.4(5) somehow deletes existing nat entries on ASA 8.4(4)1 model 5550

Created by in Network Security
12-11-2012
12-11-2012
I recently did the following configuration changes on my ASA through ASDM. The changes were the foll...

EAP-FAST with ACS 5.3 and WiSM | 5411 EAP session timed out

Created by in Wireless
12-14-2011
12-14-2011
Hi ALL,In our setup we have WiSM modules installed on cisco 6506-E, ACS 5.3 virtual appliance.We are...

Re: Unable to launch Topology Services in LMS 4.1

Created by in Network Management
11-27-2011
11-27-2011
Dear Michael,Thanks a lot for the interest. The issue seems to be resolved now. After looking at you...

Unable to launch Topology Services in LMS 4.1

Created by in Network Management
11-27-2011
11-27-2011
When I try to Launch Topology Services from windows 7 client I am getting the following error messag...

Re: BGP: How can I tell a router not to use a learned default ro

Created by in Routing
04-04-2009
04-04-2009
You can simply enter a static default route and the router will use your static default route rather...

Re: Only ping works when router is replaced

Created by in Routing
04-04-2009
04-04-2009
There are two ATMs actually hanging off the switch and the rest are remotely connected.

Re: Only ping works when router is replaced

Created by in Routing
04-04-2009
04-04-2009
Thanks Lamav,The switch ports have been properly configured to accomodate the change. In the new set...

Only ping works when router is replaced

Created by in Routing
04-04-2009
04-04-2009
OLD Setup:The old router with one Fa0/0 interface is connected to a switch. There are two subinterfa...

Cisco Works Small Network Management Solution CWSNMS

Created by in Network Management
12-29-2008
12-29-2008
Hi,I am trying to add devices (1 4506E and 2960G)to RME in CWSNMS both through the Admin->Essentials...
Public Statistics
Date Registered ‎06-18-2005 09:25 AM
Date Last Visited ‎04-03-2018 04:29 AM
Total Messages Posted 15
Helpful Votes Given To
See all >