About imagodeicommunity

imagodeicommunity · 07-17-2013

Current equipment Cisco 2901 routerCisco 2504 WLC w/2602i AP'sCisco SG300 switchesPrinter is on default vlan 1 - 192.168.0.10 addressPublic wifi is on vlan 50 - 192.168.50 xPublic wifi / Vlan 50 is currently access restricted at the router to only al...

imagodeicommunity · 06-12-2013

Problem:move existing ip phones off 10.0.0.x subnet and onto new subnet 192.168.20.xtesting the new configuration shows that dhcp is not being pulled by the phones off vlan20 but the default vlan 1 (192.168.0.x subnet)The result is the phones are not...

imagodeicommunity · 04-24-2013

Using 2901 Router and SG300 SMB mgd switches with 2504 WLC and 10 - 2601i APWas thinking of using 192.168.x.x/21 subnetted to give me 192.168.0.0 - 192.168.7.255 for 2048 hostsI was going to run everything on this flat LAN - pc, printers, wifi, lapto...

imagodeicommunity · 04-24-2013

Just purchased a 2504 w/15 licenses and to run 10 - 2602i AP'sCode out of the box is 7.0.222.0 but when I go the support site I see 7.2, 7.3 and 7.4 all with relatively recent dates. I found I need 7.2.110.0 at a minimum to run the AP's. All the code...

imagodeicommunity · 10-02-2012

I have a SPA942 that all the lights are on steady (no blinking) and there is no screen or menu.No response when I press any of the buttons. I have tried both with power and with POE connection and I get nothing.I thought maybe the SOS tool would reco...

imagodeicommunity · 06-24-2013

Test results so far.changed DHCP option to read - option 66 ip 192.168.20.230Connected test freepbx server on eth1 and set ip to 192.168.20.230set /etc/ixnetd.d/tftp file server_args = -s /tftpboot -vvvin the /tftpboot directory I c...

imagodeicommunity · 06-14-2013

Yosh...thanks for the suggestionsping ok from 192.168.0.x subnet to 192.168.20.x both directionsI did not see any ACL limitations in the router config, but could have missed it. I added a 2nd ip address to the DHCP option 150 - 192.168.0.8 and put t...

imagodeicommunity · 06-12-2013

Yosh, thanks for the response. I set port 24 to vlan20 on one of the test phones and it is now pulling the correct DHCP addressing. However, the same problem remains - not pulling the phone config via TFTP from 192.168.0.30I am wondering if I will ne...

imagodeicommunity · 10-04-2012

nsetothanks. I tried that but no success.I changed switches as well but that had no change.the switch port does not show an active connection when the cat5e cable is plugged in.yes, I have the cable plugged into the wan port not the PC port on the p...

imagodeicommunity · 06-09-2011

Nael. Our existing setup is a WLC526 with 6 LAP521G units. This setup is 4 years old and is still going ok. We do have some issues with coverage but it's been rock solid.Our office building is 55K sq ft over 3 floors and our sanctuary is 45K sq ft (...

Member Since	‎10-22-2008 12:31 PM
Date Last Visited	‎06-30-2021 12:30 AM
Posts	14

User Statistics

User Activity

I need to allow access to a company printer from unsecured public wifi

Pulling TFTP Phone configs from DHCP settings not working

Subneting vs VLAN Question

WLC 2504 needs which code version?

Linksys IP Phone SPA942 Lights all on with no screen or menu

Pulling TFTP Phone configs from DHCP settings not working

Pulling TFTP Phone configs from DHCP settings not working

Pulling TFTP Phone configs from DHCP settings not working

Linksys IP Phone SPA942 Lights all on with no screen or menu

Re: ASK THE EXPERTS : Wireless Network Management