About MATTHIAS SCHAERER

MATTHIAS SCHAERER · 02-23-2024

HiI have a 10Gb link between the two devices that is secured by MACsec/PSK. When I ping between the two devices after about 90KB of traffic I lose one ping in regular intervals. Due to the regularity I assume this is something process related but up ...

MATTHIAS SCHAERER · 11-21-2023

HiI have a highly meshed network with ASR9xx routers. The configuration of ISIS (l2 only) includes fast-reroute per-prefix level-2 allfast-reroute remote-lfa level-2 mpls-ldpon most but not all of the routers. Is it possible to have some parts of the...

MATTHIAS SCHAERER · 11-01-2023

HiI have read a lot about having different privilege levels configured with username/privilege commands. When I try to achieve this (in my case on an ASR920/V17.6.5) for a user that needs the ability to do show run (but not necessarily conf t) I do n...

MATTHIAS SCHAERER · 09-20-2023

HiThe request platform software process creates two .conf files: one packages.conf and the other one asr900rsp3-universalk9.17.06.05.SPA.conf (or whatever SW version you use). The content seems to be slightly different but not that much.The packages....

MVPN Config on ASR920 with Profile 14 · 06-21-2023

I have a 5 PE MVPN setup on ASR920 with Profile 14 (Catalyst switch in between) and I see the Lspvif going up and down regularly. On the Mcast source side I have two routers configured AnyCast RP and peered them with MSDP. The spoke side only has the...

MATTHIAS SCHAERER · 02-26-2024

Both answers did not really help but I retested the connection without MACsec and observed the same behaviour. I then attached a host to the Nexus device and repeated the pings from the C9300. With that setup I did not observe any failure (100k pings...

MATTHIAS SCHAERER · 11-21-2023

@richard: Sorry, currently no possibility to contact TAC for that matter.@MHM Cisco World: my test equipment has been moved out recently. I have to see whether I can set up a new environment.

MATTHIAS SCHAERER · 11-19-2023

There is privilege 1 for "show only" and privilege 15 for "do everything" as default in IOS and IOS XE. I often have the requirement to have have a user in between that has "show only" plus "show running-config", but no right to configure anything. T...

MATTHIAS SCHAERER · 11-19-2023

No, not really. I asked explicitly for running configuration with V17. The way I understand Richard's answer I'd have to allow all configure statements but my tests have shown that this does not change anything concerning the empty output. I have the...

MATTHIAS SCHAERER · 09-20-2023

The way you describe it asr900rsp3-universalk9.17.06.05.SPA.conf would be the more trustful file than packages.conf. Do you happen to know if there is any reason why the "request platform software clean" process deletes this file by default if it is ...

Member Since	‎04-29-2001 11:52 PM
Date Last Visited	‎03-20-2024 12:30 AM
Posts	289
Total Helpful Votes Received	42

User Statistics

User Activity

MACsec packet-loss between C9300/17.9.5 and Nexus C93180YC-FX/10.2.6

LFA/FRR ASR900/V17.6.5 question(s)

IOS/IOS XE privilege level for show running-config only Version 17.x

ASR903 packages.conf vs. asr900rsp3-universalk9.17.06.05.SPA.conf

MVPN Config on ASR920 with Profile 14

Re: MACsec packet-loss between C9300/17.9.5 and Nexus C93180YC-FX/10.2

Re: IOS/IOS XE privilege level for show running-config only Version 17

Re: IOS/IOS XE privilege level for show running-config only Version 17

Re: IOS/IOS XE privilege level for show running-config only Version 17

Re: ASR903 packages.conf vs. asr900rsp3-universalk9.17.06.05.SPA.conf