Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About gerald.suiza
01-30-2019
gerald.suiza
Beginner
Been a Network Engineer for 10 years. I worked for a major Service Provider in the United States for 3 years
Recent Badges
Stats
Member since
02-03-2011
90
Posts
54
Helpful
5
Solutions
05-25-2012
01:24 AM
hi, Thanks for the fast reply..would you know if there is any additional config or is it just the normal etherchannel config for 10G?
... View more
05-25-2012
01:14 AM
Hi, I would just like to confirm if it is possible to create a 2x10G etherchannel on a 4948. Thanks
... View more
- Tags:
- 10g
- 4948
- etherchannel
Labels:
04-02-2012
05:57 PM
Hi, I just want to clear this off my chest. We got a change and it involves adding new switches and adding new vlans. so our vendor will need to add the new vlans to the global spanning-tree config. we got something like spanning-tree vlan 1, 4, 6 priority 8192 configured. so my question is if we add vlan 45, 46, and 47 to that list using the command " spanning-tree vlan 45, 48, 49 priority 8192 will that overwrite the existing config or just add the new vlans? thanks!
... View more
Labels:
Created by
gerald.suiza
in Technical Documentation Ideas
in Technical Documentation Ideas
03-12-2012
11:52 PM
03-12-2012
11:52 PM
Hi, Has anyone run into issues with the cisco dynamic configuration tool? I recently noticed I cannot customize the hardware I am trying to configure. This was not like this in the past.
... View more
Labels:
02-19-2012
05:58 PM
Hi, could anyone point me in the right direction. not too catOS savvy I need to get the mac addresses and ip addresses off a few interfaces to which servers are connected to on a 6500 catOS switch. could point me to the commands i can issue to get these? thanks!
... View more
Labels:
Created by
gerald.suiza
in Switching
in Switching
09-19-2011
10:10 PM
09-19-2011
10:10 PM
ESX does not support LACP. You will need to configure your portchannel to "mode on". Here is a extensive document that may help you in setting up the switch. http://www.cisco.com/en/US/docs/solutions/Enterprise/Data_Center/vmware/VMware.html
... View more
09-19-2011
09:55 PM
do the unkown protocol drops increment by "1" every time you do a show interface? if it does it maybe related to a cosmetic bug. your timeouts maybe an entirely different problem.
... View more
09-19-2011
07:05 PM
personally i would go L3. once configured correctly it will work flawlessly.
... View more
09-19-2011
06:52 PM
actually its not that strange..the service provider could have inadvertently done some reconfiguration on the circuit pegging it down to 50mbps. are there any results on their investigation? did they do any recent maintenance somewhere on their network that could have affected your circuit?
... View more
09-19-2011
06:43 PM
pre-pending will take make an AS path to a peer longer which will be less preferred. so if you pre-pend on one router on the WAN peer that will make it less preferred. your two routers should have iBGP between them. i do not think you need HSRP but it may depend on what you want to achieve. lets hear what the others have to say.
... View more
Created by
gerald.suiza
in Switching
in Switching
09-15-2011
07:09 PM
09-15-2011
07:09 PM
use this to specify the boot image location: boot system flash bootflash: [image name]
... View more
09-07-2011
07:32 PM
try and source your ping on the router from the LAN segment subnet
... View more
09-06-2011
05:33 PM
I would also make sure what the HP blade protocol is for NIC teaming or else the config wont work..protocol mismatch
... View more
09-05-2011
07:31 PM
have you checked layer 1? i would check layer 1 first instead of looking at BGP
... View more
05-25-2012
hi,Thanks for the fast reply..would you know if there is any additional
config or is it just the nor...
05-25-2012
Hi,I would just like to confirm if it is possible to create a 2x10G
etherchannel on a 4948.Thanks
04-02-2012
Hi,I just want to clear this off my chest. We got a change and it
involves adding new switches and a...
Created by
gerald.suiza
in Technical Documentation Ideas
03-12-2012
03-12-2012
Hi,Has anyone run into issues with the cisco dynamic configuration tool?
I recently noticed I cannot...
02-19-2012
Hi,could anyone point me in the right direction. not too catOS savvyI
need to get the mac addresses ...
Created by
gerald.suiza
in Switching
09-19-2011
09-19-2011
ESX does not support LACP. You will need to configure your portchannel
to "mode on". Here is a exten...
Created by
gerald.suiza
in Routing
09-19-2011
09-19-2011
do the unkown protocol drops increment by "1" every time you do a show
interface? if it does it mayb...
09-19-2011
actually its not that strange..the service provider could have
inadvertently done some reconfigurati...
09-19-2011
pre-pending will take make an AS path to a peer longer which will be
less preferred. so if you pre-p...
09-06-2011
I would also make sure what the HP blade protocol is for NIC teaming or
else the config wont work..p...
Created by
gerald.suiza
in Routing
09-05-2011
09-05-2011
have you checked layer 1? i would check layer 1 first instead of looking
at BGP
Public Statistics
| Date Registered | 02-03-2011 09:56 PM |
| Date Last Visited | 01-30-2019 06:50 PM |
| Total Messages Posted | 90 |
| Total Helpful Votes Received | 54 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "Hall of Fame Guru"){kind=icon}
Helpful Votes From
