About Liv_Liv

Liv_Liv · 06-13-2022

Hi, I am dealing with a SIP trunk installation in India (provider Tata). The provider has registration & authentication as a requisite and now they are requesting us to change all our sip traffic in order to communicate with them with source port a...

Liv_Liv · 09-21-2021

Hi, I am testing the following setup: CUCM -- SIP trunk -- ISR 4331 -- PRI Like I said this is a test environment so the PRI are not yet plugged in the NIM E1 cards. So the inbound/outbound dial-peers tied to the PSTN are down by now. So Im testing...

Liv_Liv · 06-24-2021

Hi, Im just trying to set up a brand new UCS-C220-M5 and having serious difficulties, After configuring the CIMC addressing, I found out that the hard drives (6 x SAS SFF HDD) are not being detected. I need to get to the Hypervisor configuration util...

Liv_Liv · 06-23-2021

Hi, I have the following setupCUCM PUB + SUB System version: 11.5.1.15900-18 Everytime a backup is attempted (no matter if its scheduled or manual), when all components are backed up and each one of them show "100% SUCCESS", the process get stuck in ...

Liv_Liv · 06-22-2021

Hi,Im setting an ISR4K (4331) with IOS XE Fuji for voice functionality connected to a providers on-premise router for SIP trunking and voice functionality.The specs datasheet from the provider states that for the voice functionality to work over thei...

Liv_Liv · 06-13-2022

Thanks again @b.winter the command "source-port" might be what Im looking for in order to change UDP to 5061 as a source port in my SIP requests. However I tried to look for this command under voice service voip level, sip level, sip-ua level and d...

Liv_Liv · 06-13-2022

Hi, thanks for your reply !! Indeed the suggestion you posted did work for destination port without an IOS upgrade, thanks for the tip my main issue here is now in doing the same thing for source port 5061, I still need this to be accomplished by...

Liv_Liv · 09-22-2021

thank you both @Roger Kallberg and @Maren Mahoney for confirming what I was thinking. So I ended up having a knowledge/concept issue rather than a real config issue. I thought that the call routing logic in a gateway checks potential matches before ...

Liv_Liv · 09-21-2021

Hi all, ended up opening TAC case. Problem was I was hitting bug CSCuu46430 related to DRF process creating logs without purging them, ence not finishing properly. https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuu46430/?rfs=iqvred Thing is, the on...

Liv_Liv · 06-24-2021

Hi Nithinthanks for your suggestion. I will try to reseat the controller tomorrow at office and get back to you with the results. However Im worried because at this stage the server is unresponsive no matter what key you press on the splash screen, I...

Member Since	‎05-28-2013 05:31 AM
Date Last Visited	‎06-20-2022 08:30 AM
Posts	42
Total Helpful Votes Received	35

User Statistics

User Activity

CUBE - ¿Change source and destination ports for ALL SIP traffic?

"No matching outgoing dial-peer" on ISR 4K for outgoing calls to PSTN

UCS BE6M-M5-K9 not booting up - stuck in CISCO splash screen

CUCM backups not being completed - stuck at final step "Copying backup TAR file to archive media"

PPPoE enablement & config on ISR 4K - IOS XE for automatic DNS and routing from ISP

Re: CUBE - ¿Change source and destination ports for ALL SIP traffic?

Re: CUBE - ¿Change source and destination ports for ALL SIP traffic?

Re: "No matching outgoing dial-peer" on ISR 4K for outgoing

Re: CUCM backups not being completed - stuck at final step "Copyi

Re: UCS BE6M-M5-K9 not booting up - stuck in CISCO splash screen