About Rajesh Kongath

Rajesh Kongath · 02-21-2023

Hi All,We are in the process of moving Static VLANs to Dynamic VLANS from our SD Access fabric site, we need your support on an issue.We have critical VLANs (both data & voice) assigned for the VN. Dynamic VLAN works without any issues for the VLANs ...

Rajesh Kongath · 01-15-2023

HiAnyone point me the rigth documentation on upgrading Cisco Prime infrastructure (PI) 3.9 to 3.10 version? For the versions until 3.9 i found useful instructions in the quick start guide, however for version 3.10 there is nothing mentioned about upg...

Rajesh Kongath · 11-27-2022

HiIs there any way to display cdp information of APs on c9800 (17.6.3) controller in GUI? I am looking for the command output of "sh ap cdp neighbors" in the GUI. AirOS based WLCs had an option to view this on GUI Home> Network summary > Access point...

Rajesh Kongath · 10-12-2022

HiWe are running a fully lan automated, SDA Fabric network with DNAC version 2.2.3.4 & C9300 IOS 17.3.4. We wanted to switch to host macsec, below given a sample commands for the while we are doing thru the CLI.I would like to know What is the best p...

Rajesh Kongath · 08-27-2022

HiDNAC 3 Node Cluster version 2.2.3.4 We seeking help on RMA process for on of our LAN Automated faulty CAT 9300 series switch. We are following the 2.2.3 user guide however it doesnt have much clarity on the RMA process. We knew that from 2.2.3 vers...

Re: Adding stack member using dnac · 03-20-2023

I found a better workaround for this issue. DNAC > Design > Network Settings > Go to the affected site/floor > Disable wired end point data collectionDNAC > Provision > Inventory > Go to affected site > select affected device > Action > Telemetry > U...

Rajesh Kongath · 03-19-2023

I found a workaround for this issue, DNAC > Design > Network Settings > Go to the affected site/floor > Disable wired end point data collectionDNAC > Provision > Inventory > Go to affected site > select affected device > Action > Telemetry > Update...

Rajesh Kongath · 03-19-2023

HiUsually it gets pushed while doing the discovery, or you may have to add with CLI Templates. https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and-management/dna-center/2-3-3/user_guide/b_cisco_dna_center_ug_2_3_3/b_...

Rajesh Kongath · 10-13-2022

Thank You @willwetherman & @Sylvain_Che - allow me to ask a few more questionsMacSec needs host-mode multi-domain, which I believe can be achieved via selecting no of hosts "single" by editing closed authentication settings in DNAC. But in our scenar...

Rajesh Kongath · 08-29-2022

Thank you For the reponse, the PDF refers to an old DNAC, DNAC 2.2.3.4 supports RMA for Lan automated. I think There is no complete automated or zero touch way of RMA, you have to connect the replacement switch to network and do a pnp or manual disco...

Member Since	‎04-30-2006 12:32 AM
Date Last Visited	‎03-27-2024 12:16 AM
Posts	88
Total Helpful Votes Received	55

User Statistics

User Activity

Critical VLAN Static IP

Upgrade - Prime Infrastructure 3.9>3.10

C9800 AP CDP

DNAC|SDA|MACSec

DNAC 2.2.3 RMA for LAN Automated device

Re: Adding stack member using dnac

Re: DNA SD-Access Interface Configurations

Re: DNA IPDT_POLICY doesn't apply to all ports

Re: DNAC|SDA|MACSec

Re: DNAC 2.2.3 RMA for LAN Automated device