Hello,   Just need a little help with choosing an external MIC with Cisco 8861 IP Phone. The voice from Cisco inbuilt speaker is fine but the voice of the participant is not reaching well on the other side when he is little far away from IP Phone. Please suggest a model and do let me know if somebody has been using the same too.   Thanks.   Regards, Ashish Bagla   ... View more

Hi, We have a CUCM 10.5.2 integrated with AVAYA SME. Avaya SME is connected to other sites on Avaya and Nortel. Now there is an PSTN MVA number 441275 which has been translated on router as 446220 and the MVA works properly i.e. we are able to dial PSTN calls when we are dialing from mobile. The problem is when we want to reach the DISA number i.e. 446220 via Avaya SME from any other site to call via MVA. Can this be achieved too as MVA works from router and how the communication would happen if call comes via Avaya SME SIP trunk by calling 446220 directly? The call does not gets connected to MVA IVR only. Any Help would be appreciated.. Regards, Ashish Bagla ... View more

Hi ,   I am getting the below error on RTMT on CUCM 9.1 Version running on MCS 7835-I3-K9-CMD2 Error    At Sat May 24 03:12:40 IST 2014 on node , the following HardwareFailure events generated:  hwStringMatch : May 24 03:12:23 ASHISH-CM01 daemon 4 Director Agent: LSIESG_AlertIndication 500605B005F63930 Consistency Check inconsistency logging disabled on VD 00/0 (too many inconsistencies) Sev: 3. AppID : Cisco Syslog Agent ClusterID :  NodeID : ASHISH-CM01  TimeStamp : Sat May 24 03:12:23 IST 2014    hwStringMatch : May 24 03:12:23 ASHISH-CM01 daemon 4 Director Agent: LSIESG_StorageVolume_Modified 500605B005F63930 Consistency Check inconsistency logging disabled on VD 00/0 (too many inconsistencies) Sev: 3.   AppID : Cisco Syslog Agent ClusterID :  NodeID : ASHISH-CM01  TimeStamp : Sat May 24 03:12:24 IST 2014   Does anybody has any idea on the same.   Your inputs would be appreciated ..   Regards, Ashish Bagla ... View more

Hi Team, Our setup has been recently upgraded to CUCM 9.1 ( Publisher and Subscriber ) and has an Voice Gateway for PRI termination but the same has been used as CME in SRST mode and is still at version 8.1 Our primary concern is that the firmware of the IP Phones if there is an situation if it has to fallback on it. Will we need to upgrade the firmware files for the CME using the same firmware files which are being used for CUCM currently. Current firmeware of 7962 on CUCM 9.1.2.11008_1 SCCP42.9-3-1SR2-1S   Current firmeware of 6941 on CUCM 9.1.2.11008_1 SCCP69xx.9-3-3-2-SR1   Previous firmware of 7962 on CME in fallback mode - 8.1 with flash c3900-universalk9-mz.SPA.151-2.T1.bin P0030702T023.loads P0030702T023.bin P0030702T023.sb2 P0030702T023.sbn    hostname#sh telephony-service CONFIG (Version=8.1) ===================== Version 8.1 Max phoneload sccp version 17 Max dspfarm sccp version 18 Please let me know on the same. Thanks in advance. Regards, Ashish Bagla ... View more

Hello, We have MTNL's BRI line terminated on VOICE Router and shows MULTIFRAME also. My outgoing calls are working through BRI line with proper caller ID. We want to know, when an incoming call is comming, the calling party mobile number is being displayed correctly, but called party number of the BRI is not being shown, while we debug it through debug isdn q921 and q931. Does the normal BRI shows the called party number also. Please confirm. I have added my debug output for your reference. Calling Number - 8879628934 and Called Number - 26875175 (Not Being Dispalyed)   014991: Apr  7 12:05:16.888: ISDN BR0/1/0 Q931: RX <- SETUP pd = 8  callref = 0x01         Sending Complete         Bearer Capability i = 0x8090A3                 Standard = CCITT                 Transfer Capability = Speech                 Transfer Mode = Circuit                 Transfer Rate = 64 kbit/s         Channel ID i = 0x89                 Exclusive, B1         Calling Party Number i = 0x2183, '8879628934'                 Plan:ISDN, Type:National 014992: Apr  7 12:05:16.892: ISDN BR0/1/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x81   This call gets disconnected automatically on router itself and doesnot land on IP Phone.   Appreciate your help.       ... View more

Hi, I am going to install Meeting place 8.5.2 on MCS 7835-i3-RC1 Server with 4 GB RAM. It is said that its may cause some performance degradation. Need to know this in more details what could be degraded like voice quality or meeting schedules etc. Any help would be appreciated. Thanks. Ashish Bagla ... View more

Hi, CUPS version is 8.0(4) and Jabber for Windows version is 9.0(5). I have integrated CUPS with CUCM through SIP trunk. When I type a number in the strip provided at the top and press enter, the number that I typed disappears and call does not go. Any solution for this will be appreciated. thanks. ... View more

Hi, Call manager - 8.0 version. IP phones - 7962, 7975. Incoming call rings even the caller disconnect the call. Pl guide if anybody have the solution. Regatds Ashish. ... View more