About Jacobo Schneider

Jacobo Schneider · 03-01-2017

Hello, I want to validate if the ASR9010 with RSP880 is able to handle eight (8) 8x100 Linecards at line rate. My confusion is because I'm not sure if the 880Gbps is the limit of the switch fabric on the RSPs, so having the chassis full of 8x100Linec...

Jacobo Schneider · 02-19-2017

Hi, We have an old GSR12410 running IOS and we want to migrate it to XR. Target release is XR 4.2.4 which is already running in the network. I have only found documentation to migrate IOS to XR3.8.0, http://www.cisco.com/c/en/us/td/docs/ios_xr_sw/i...

Jacobo Schneider · 03-04-2016

Hi, I'm wondering if there is a way to get the output of the "sh mfib vrf xxx route rate" using SNMP.I would like to monitor and graph the rate of each (S,G) over time. Does someone know if there is an OID to get this info?? This is for ASR9000 usin...

Jacobo Schneider · 01-20-2016

Hi, I'm wondering if Profile 10 (p2mp-te with static mapping in VRF) is supported in ASR9000 XR I configured according to this link http://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/multiprotocol-label-switching-vpns-mpl...

Jacobo Schneider · 01-14-2016

Hi, I have a multicast network where the Source is in a LAN that have 2 PIM routers. These two routers must be each the head of one P2MP-TE Tunnel. The two tunnel are destined to the same set of tails but each one explicitly route over separate path....

Jacobo Schneider · 03-02-2017

Thanks so it seems that a ASR9010 with dual RSP880 has a composite switch fabric handle 6.4 Tbps to have 800Gbps line rate per linecard, right? Jacob

Jacobo Schneider · 10-28-2016

Hello, A doubt I have had is the purpose of the second management interface on each RP. All configurations I have seen that interface is shutdown. Does this interface can be used in the same subnet to provide further redundancy, or it has to be in a...

Hi Giuseppe, thanks for your · 01-26-2016

Hi Giuseppe, thanks for your answer, I managed to get the configuration to work just yesterday, actually by mistake I didn't enable PIM on the loopback which was the root cause of the problem. Now, aside from my lab is now working, it seems to me t...

Jacobo Schneider · 08-27-2015

Hi Ali,It seems to me that your customer maybe using UDP (or session-less) traffic, because TCP will react and slow down the transmission rate when you perform the drop action in either direction. However if you are the issue for TCP traffic you coul...

Jacobo Schneider · 08-27-2015

Hi Prashant,Networks are not entered in the BGP table because the exact networks specified in the network statement under BGP are not present in the routing table. This statement without the "mask" option assumes the classfull boundary which in your ...

Member Since	‎08-29-2011 06:24 AM
Date Last Visited	‎08-18-2017 04:03 AM
Posts	21
Total Helpful Votes Received	5

User Statistics

User Activity

ASR9000 RSP Maximum Switching Capacity

GSR12410 - IOS to XR migration

How to get Multicast Flow Rate via SNMP - ASR9000

Does ASR9000 support NG-MVPN Profile 10 ??

How to provision two P2MP-TE Tunnels from two different headend to the same tailends for multicast

Thanks so it seems that a

Hello,

Hi Giuseppe, thanks for your

Hi Ali,It seems to me that

Hi Prashant,Networks are not