About Mohammed Al-odhari

Mohammed Al-odhari · 02-08-2021

Dears,I have a cisco router configured with MGCP to the call manager. FXO ports shown as registered in the CUCM but FXO is no not working.It shows in the Cisco Voice GW as ring-dect then up status. and keeps ringing or some time ring once and disconn...

Mohammed Al-odhari · 01-09-2021

Dears,Hope you are doing wellI have the following scenario; Error "SIP/2.0 404 Not Found" CME (ver 8.5) SCCP IP Phone(212)-->LAN(SIP Trunk)-->Grand Stream UCM 6208 Device--> SIP IP phone(6000)--> Fast Busy Signal......But the opposite direction wo...

Mohammed Al-odhari · 01-01-2020

Dear All,am having cisco cme router 2921 with version 9 cme.I need to get the calls log reports in the same format of cme report-->call history (start time - originating number - destination number - duration) for a long period of time like 3-6 month...

Mohammed Al-odhari · 12-17-2019

Dear all,I have an old CUCM7-BE (MCS7828H3-K9-BE7) with about 1800 DLU units (only 900 DLU used) in addition to 50 mail box in the unity connection. Branches there are MGCP gateways works also in SRST when CUCM fails. Models are (2851,2811,1861,2911 ...

Mohammed Al-odhari · 03-16-2019

Dear all, I have 3 FTDs 2100 version 6.2.3 connected and configured by Virtual FMC (6.2.3). Two of the three FTDs are configured in HA mode as per attached. I want to break the HA in which FTD_02 which is the active (as attached) keeps working and pr...

Mohammed Al-odhari · 02-10-2021

Dear Scott,This post is for after the internal phone rings but don't hand up, my issue is at the beginning in which I want my internal phone number to ring, it keeps showing ring-det status then up status only with ring tone sound. regards,

Mohammed Al-odhari · 02-09-2021

Hi again,I remove MGCP and configure H323 , shows same issue for FXO port ring-det status. regards

Mohammed Al-odhari · 02-09-2021

Hi Nithin again,Ignore any PLAR setting under the voice ports, it is already removed. Yes MGCP is rare but this settings is working fine for 10 years till last week. Attached is the MGCP CUCM settings as requested.All previous issues for the whole pe...

Mohammed Al-odhari · 02-09-2021

Thanks Scott for your replay.here you go for the main show run settings as per requested. The difference in the error code , i think because of the different applied settings under the voice ports as some times caller hears ringing tone only and some...

Mohammed Al-odhari · 02-09-2021

Hi again Nithin,Both of your above configuration was already there,i have attached you another debug files for two test calls as below:The first call is to voice-port 0/0/1 and the second call is to voice-port 0/0/0.Calling number: 771484383Called id...

Member Since	‎02-02-2011 08:17 AM
Date Last Visited	‎02-14-2021 03:48 PM
Posts	474
Total Helpful Votes Received	17

User Statistics

User Activity

FXO ring-dect issue

SCCP to SIP phone busy tone issue

CME call report logs to syslog server in table view format

CUCMv7 migration to CUCMBEv12 questions

FMC Breaking HA questions?

Re: FXO ring-dect issue

Re: FXO ring-dect issue

Re: FXO ring-dect issue

Re: FXO ring-dect issue

Re: FXO ring-dect issue