Hi all,   Got a 3802i (8.3.102.0) and want to use it as an access-point to do site-survey. I went through the document and got stuck in the below process Step 7   To configure channel, TX power, and channel bandwidth for the radios, disable the radio first, make the changes and then re-enable it. To change the 2.4GHz radio to channel 6, follow the steps below: (Cisco Controller)>config 802.11b disable <ap name> (Cisco Controller)>config 802.11b channel <ap name> <ap name> 6 (Cisco Controller)>config 802.11b enable <ap name> To change the 2.4GHz radio Transmit Power to power level 3, follow the steps below: (Cisco Controller)>config 802.11b disable <ap name> (Cisco Controller)>config 802.11b txPower <ap name> <ap name> 3 (Cisco Controller)>config 802.11b enable <ap name> To change the 5 GHz radio to channel 44, follow the steps below: (Cisco Controller)>config 802.11a disable <ap name> (Cisco Controller)>config 802.11a channel <ap name> <ap name> 44 (Cisco Controller)>config 802.11a enable <ap name> To change the 5 GHz radio Transmit Power to level 5, follow the steps below: (Cisco Controller)>config 802.11a disable <ap name> (Cisco Controller)>config 802.11a txPower <ap name> <ap name> 5 (Cisco Controller)>config 802.11a enable <ap name> To change the 5 GHz radio channel width to 40MHz, follow the steps below: (Cisco Controller)>config 802.11a disable <ap name> (Cisco Controller)>config 802.11a chan_width <ap name> 40 (Cisco Controller)>config 802.11a enable <ap name>     the mobility express wlc doesnt recognize itself as an ap. Can this be achieved? 3802i acting as WLC and AP servicing clients (FAQ says yes) any help is appreciated. I also keep getting the error message Config not synced to APs since no AP is present   regards ... View more

Hello.   Has anyone encountered the below issue? When i try to hotspot through iphone it asks for password, once i put in the credentials it just wont work and the NAM falls back to the wifi connection. It also doesnt work if we try to add any home wifi ssid. It only works for corporate enterprise wlan and wired network. Any ideas?   regards ... View more

Hello,   I am currently test AC4.6 with windows 10 SOE. I got the VPN,NAM and ISE posture module installed. Once the authentication is finished, the windows10 laptop opens a browser session (device security check) straightaway before the compliance check is completed. I wonder what causes the browser session to be opened. Any inputs are appreciated.   regards   ... View more

Hi, I am trying to create a posture requirement with two conditions (both are user defined). When i add my second condition i get an error (attached). I want to check if a specific McAfee version is installed and a specific process is up and running. If i add a cisco defined condition as my second one it accepts. Any ideas?   regards   ... View more

Hi all,   ISE Posture check before login into computer - wired dot1x - can this be achieved? We are running Cisco ISE v2.1 patch 3 Posture check requirement: 1) AV service enabled 2) updated AV DAT file - checks the registry for date 3) whitelisting software service enabled Authentication: Machine certificate   this works fine after login but we use local script to map drives for the users because group policy wont let map drives while the computer is checking the posture. I wonder we can do this posture check and put the machine in right vlan before the user logon.   regards     ... View more

Hi, Fairly new to ISE (running v2.1), we are trying to implement wired dot1x monitor mode for the end users. We check AV service running and latest dat file for posture but allow user to override it if posture fails as it is only a monitor mode deployment. I have attached the screenshot of the message that appears to users when posture fails, i want to customize the message in the text and also dont give the option "START" for the users to click. Appreciate your thoughts. regards ... View more